Jump to content
SAU Community

Recommended Posts

G'Day

I am parting out my track 32 gtr

Complete front end, bonnet, guards, front bar, lip and reo. It is off a track car so has bonnet pin holes a few small dents in the guards and a slot cut in the front bar. Still looks tough $1,000.00

Big exhaust $80.00

Front pipe $80.00

Crs Dumps $280.00

Cusco gear has been on the car for 5 lap of Malalla

Cusco Front sway bay $200.00

Cusco front negative camber upper arms -5mm $250.00

Cusco adjustable bar that goes between the castor rod mounts $100.00

Cusco rear sway bar $200.00

Not cusco front strut brace $80.00

Front drive shafts reconed at OG CV joints (no play) $90.00 each

R34 GTR turbos $350.00

6 Point cams approved with paperwork bolt in cage with side intrusion bars - made by Nick from Buddy Parts $1,800.00

post-41741-0-55666900-1338260194_thumb.jpg

What sizes are your sway bars?

Also, are the headlights genuine N1's with moulded plastic clips or are they the GTS-t version with metal clips for the grill?

What sizes are your sway bars?

Info from the order the front is 24mm and the rear is 30mm. Google the Part No. for full description *** They are hollow ***

> 1x 231 479 AC Cusco FRONT Negative Camber Upper Arms -5mm for BNR32

> 1x 231 311 A Cusco FRONT Sway bar for BNR32

> 1x 231 311 B Cusco REAR Sway bar for BNR32

1x 231 485 A Cusco Tension Rod Bar for BNR32

Also, are the headlights genuine N1's with moulded plastic clips or are they the GTS-t version with metal clips for the grill?

The headlights are not in the $1000.00 but they are for sale, I will investigate the clips tonight.

post-41741-0-10531300-1338372365_thumb.jpeg

Cusco goodness with mint driveshafts

post-41741-0-00608600-1338372384_thumb.jpeg

CES Dumps good quality locally made dumps

post-41741-0-29082900-1338372411_thumb.jpeg

Don't know what make it is but it is 93mm in Diameter

post-41741-0-79915400-1338372440_thumb.jpg

R34 Turbos

post-41741-0-08730900-1338374025_thumb.jpegpost-41741-0-26818700-1338374045_thumb.jpeg

I have drilled a couple of holes in the guards to cable tie the front bar on and they have been rolled.

how did your car handle with all this cusco goodness? over steer / under steer etc.

how did your car handle with all this cusco goodness? over steer / under steer etc.

It was better than the stock bars as I was running slicks and they made it lean a fair bit. I can't really comment on the balance as I only ran 5 laps, but I assume some cusco propeller head would have made them match.

How much would you sell front bar for? also whats the condition, dents, chips ect.. cheers bud

$200 with the reo and lip, It needs work / paint and I have cut a slot in it for the tow loop.

Tried to PM, but you must be full.

Would you be interested in parting out the grill?

Thanks

Yep $100.00 I also have the original mesh $50.00

post-41741-0-67707900-1338590922_thumb.jpg

More Cusco goodness.

I have had a look at the front guards and they are a bit rough so $250 for the pair.

Bonnet $300.00

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Strange your posting about this being an issue. Move the harness or change your wheels or run more camber etc. Have the thing not touch the thing so it doesn't destroy the thing.  Short answer, no. Slightly longer answer, the factory fuel gauge is measuring resistance. You need to wire in the FPG fuel level sender into the original factory fuel level sender wiring.  I drew you a picture to explain this one The factory strainer is quite long, reaching down into the bottom of the tank. Safe bet your aftermarket fuel pump has a little baby sized strainer that probably doesn't even point down towards the bottom of the thank.  Solution, move the pump lower down in the tank, or fit a longer strainer, or do both. I did both, I've run my tank down to 5L remaining and the car still drove fine.   
    • S2/3 GT-R is the same as S2 GTS-t The SRS airbags module in under the centre console. The S1/S1.5 GTS-t and S1 GT-R had the module built into the steering wheel. FWIW, I have a S3 GT-R wheel in my S2 GTS-t shit box. Same airbag plug, airbag light goes on then off, meaning all systems are go. S3 GT-R has red stitching, that's about it.
    • Dumb question, but why would it matter if the wheel came off a car with hicas or not?
    • Hey to anyone that reads this, long time lurker first time posting, sorry if it’s been answered before but I’ve been looking for nearly a year now for answers. ive got a 25det neo in an r32 that works awesome when it works (made 500whp on 21psi) but works 45% of the time, 1st issue there’s a harness that runs under the passengers side front fender that my tire keeps rubbing through and one wire seems to power the fuel pump even though I’ve done the relay “mod” some people like to call it, and when it does rub through it kills the car, yes next time I’m with the car I want to take the fender off and try tuck the harness well out of the way but I’d also like to try and by pass this mysterious wire as well lol, also wouldn’t mind getting power from the alternator as I’ve read it supplies the pump with 13v ? But no idea where to run the power wire too. 2nd issue, when replacing my fuel pump and fuel hanger I managed to break the factory fuel level sender leaving me with no fuel gauge, I’d like to buy the fpg fuel level sender for r32/s13 but the plug it comes with confuses me, I’ve got a detschwerks x1 fuel hanger which has light + pump - level + pump + and a ground, I’m no auto sparky but I’m wondering if I can cut the plug off the fuel level sender and wire the negative to the pump negative and wire the positive to the level positive to get a fuel gauge back ?🥴 3rd and final issue, the reason I want a fuel gauge is because whenever it’s below half a tank, it fuel starves like crazy and runs like a bag of shit even without doing a pull or sloshing the fuel round in the tank, I’d also like to fix this but have no idea what’s causing it, I’ve got a dw420 and a dead head fuel setup meaning the fuel is regulated before it gets to the engine, my only theory is that the return line is to close to the pickup on the pump and when it’s at half a tank the return line is causing the pump to cavitate enough to cause fuel pressure issues, that or the pump isn’t low enough in the tank which I would find strange considering I can’t find a single thing online about it, also if ya wondering how I figured out it happens at half a tank without a fuel gauge, I waited until it started happening and went and filled up and the car took exactly 30 litres every time I tested it, if ya managed to read through this mess I appreciate that and any recommendations , cheers
    • ChatGPT is trash and lies about things I would not expect it to lie about considering many things it's wrong about are very easily verified with google. The S3 R33 GTR shares its steering wheel with R33 GTSTs of the same production year. Part number is 48430-26U17. I'm guessing you have to get it from a car that came with HICAS though, the ER33 is 48430-26U18, but the HR33 diagrams note that part number is still leather vs 48430-26U13 which is not leather-wrapped. They all use the same airbags, so if you need another one you can get it off basically any same year R33 or Stagea.
×
×
  • Create New...