Jump to content
SAU Community

Fastest Stagea Over A Quarter Mile?

GTR260

By GTR260,
in Four Door Family & Wagoneers

 Share

Recommended Posts

numleg Community Regular

numleg

Posted
Posted

I know there are faster Stageas out there but mine runs 12.3 quaters on 265/35/18 rubber in full street trim.

Mods list:

Stock bottom end

Stock FPR

R34 GTR turbos

Nismo 555cc injectors,

Walbro fuel pump

Power FC

AVCR

Z32s

Greddy suction kit and cold air box with factory snorkel

HKS 264 deg cams

HKS cam gears

HKS hard piping kit

Yoshida Garage custom ported head and port matched exhaust manifolds

Greddy extended split dumps and front pipe

Fujitsubo Cat back

Gutted cat

N1 oil and water pumps

Greddy oil cooler kit

Turbosmart BOVs

Fried exedy HD clutch

Unknown mechanical LSD

GTR struts with low kings springs in the front, Tein lowerd struts/springs rear

312.5kW at 16.5 psi

272kW at 13 psi

WAGON_BOY Mentor

WAGON_BOY

Posted
Posted (edited)

here's the official thread :whistling:

http://www.skylinesaustralia.com/forums/topic/389668-the-official-sau-stagea-facts-and-figures-thread/page__hl__mile

Edited by WAGON_BOY
coparts41 Community Regular

coparts41

Posted
Posted

I seem to have read another post somewhere about a guy in sweden or around there somewhere , had his own dyno and got low 11~s or high 10s at the drags . pretty Vague i know maybe someone else read it too?Seems he just kept on increasing the boost until it blew, i think the 9000rpm was the killer.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
    • GTSBoy
      AC not coming from top vents

      By GTSBoy · Posted

      What HVAC actuator is under the steering wheel? Do you mean on the RHS of the centre console, immediately to the left of your shin? If so, then yes, it is probably that one, because that is the mode door actuator, and from what I know, it's still a pain in the arse to replace. I don't know about whole dash out, but you certainly have to rip into the centre console section. I don't know if it's covered in the workshop manual, as I haven't spent much time looking at those parts of it. (and by "the workshop manual, I mean the R32 GTR one, which is the most comprehensive one we have, and it should be similar enough between that and later cars to serve as a guide).
    • dbm7
      Shifting questions

      By dbm7 · Posted

      ...oops. forgot the TCU end...
    • Sleepergm
      Custom titanium intake

      By Sleepergm · Posted

      No I got mine from a friend that had fabricated one … but I had to fit it to my setup which was a hks turbo setup. His was a Garrett -7. So one of my turbos was not a flange for one side … then I had a leak in the welds I had to find a weld shut … in the end the setup was decent priced but I spent a lot to get it fitted. A couple companies I checked would make it but you’re talking 7-9k aud with titanium. No joke mine was 6-7k even second hand after I had to fit it in Hong Kong … labour is expensive here. 
    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      I'd just like to restate that I don't think anyone here is actually hating I recently sold a car part to a guy who was building a forged auto R34, with MV stall and aiming at ~450kw. I told him that I'm him, from the future and to stop after it explodes once. I told him I knew he won't listen the first time, and that's fine. But if my predictions do come true - Change direction faster than I did. I also said it's probably no coincidence that the dyno plot of a reliable turbo engine starts to look a lot like a N/A motor. :p
×
×
  • Create New...