Jump to content
SAU Community

Recommended Posts

Sorry to Hi-jack your thread but does anyone know with "street semi's" like Federal RSR's for example is there any point in warming them up at the drags or are they the same as normal street tyres that don't like heat?

Sorry to Hi-jack your thread but does anyone know with "street semi's" like Federal RSR's for example is there any point in warming them up at the drags or are they the same as normal street tyres that don't like heat?

its always good to warm up the tyres this will give you bit of extra grip , you probably seen other cars running semi or even full slick still warming them up.

its always good to warm up the tyres this will give you bit of extra grip , you probably seen other cars running semi or even full slick still warming them up.

I under stand the guys with race tyres warming them up coz race tyres only work at a certain operating temp's but street tyres are designed not to need to be warmed up to be able to produce grip & iv been told heating them can actually make things worst. So just wondering how these street semi's work.

It comes down to how much power your car is putting down and how serious you are.

Do you have a 185kw, FMIC, exhaust, filter car or a 300kw, GT3076 + supporting mods car or a 350+, forged, gt35 + all the fruit car?

If it's 185, a warm up is pointless, traction won't be an issue. If it's ~300ish then it might be of use you're running street tyres, but in reality you'll do better simply managing your throttle and clutch better. If it's the last option, then I would expect you are running slicks and intend on launching hard and a warm up burn out is definitely beneficial (if not slicks then no amount of street tyre burnout is going to stop you wheel spinning for a good portion of the race).

So, in conclusion, I'm going to bet your running moderate power on street tyres which means a pre race burnout is going to give very limited benefit. But do one anyway, cause they are fun :)

I under stand the guys with race tyres warming them up coz race tyres only work at a certain operating temp's but street tyres are designed not to need to be warmed up to be able to produce grip & iv been told heating them can actually make things worst. So just wondering how these street semi's work.

pretty sure the tyres will be warming up regardless, when doing a burn out you give the tyre the chance to grip the surface properly when taking off i own MT semi slick tyres and yes they are meant to be warmed up , those that dont properly dont have the option to, however from experience , it works.

Edited by Hiroshima Screamer

It comes down to how much power your car is putting down and how serious you are.

Do you have a 185kw, FMIC, exhaust, filter car or a 300kw, GT3076 + supporting mods car or a 350+, forged, gt35 + all the fruit car?

If it's 185, a warm up is pointless, traction won't be an issue. If it's ~300ish then it might be of use you're running street tyres, but in reality you'll do better simply managing your throttle and clutch better. If it's the last option, then I would expect you are running slicks and intend on launching hard and a warm up burn out is definitely beneficial (if not slicks then no amount of street tyre burnout is going to stop you wheel spinning for a good portion of the race).

So, in conclusion, I'm going to bet your running moderate power on street tyres which means a pre race burnout is going to give very limited benefit. But do one anyway, cause they are fun :)

you haven't been to the drags much have you? i was having traction issues with about 180hp (so about 135kw) in my magna. a mate of mine had a sr20 in a sigma and with street slicks he was lifting one of the front wheels off the ground when launching and he only had about 250hp. he was simply holding it on the rev limiter and pretty much just side stepping the clutch. his 60' times were around 1.5 seconds.

you haven't been to the drags much have you? i was having traction issues with about 180hp (so about 135kw) in my magna. a mate of mine had a sr20 in a sigma and with street slicks he was lifting one of the front wheels off the ground when launching and he only had about 250hp. he was simply holding it on the rev limiter and pretty much just side stepping the clutch. his 60' times were around 1.5 seconds.

Actually, I have.

My 33 was a typical 11psi, FMIC, exhaust and pretty healthy. I had china specials on the back and traction was never an issue. I could light up the rears in first and a tiny chip/squirm into second if I wanted, but by christ I had to be pumping it pretty friggin' hard. Pull back to 95%, which is sensible if it's your daily, and traction was not an issue.

It comes down to how much power your car is putting down and how serious you are. Do you have a 185kw, FMIC, exhaust, filter car or a 300kw, GT3076 + supporting mods car or a 350+, forged, gt35 + all the fruit car? If it's 185, a warm up is pointless, traction won't be an issue. If it's ~300ish then it might be of use you're running street tyres, but in reality you'll do better simply managing your throttle and clutch better. If it's the last option, then I would expect you are running slicks and intend on launching hard and a warm up burn out is definitely beneficial (if not slicks then no amount of street tyre burnout is going to stop you wheel spinning for a good portion of the race). So, in conclusion, I'm going to bet your running moderate power on street tyres which means a pre race burnout is going to give very limited benefit. But do one anyway, cause they are fun :)

I dono my R34 was only making 165rwkw & i was having some pretty big traction issue. Had to baby it off the line (holding it at about 3 grand, slowly stepping off the clutch & waiting before I went to WOT) otherwise I went no where just spun.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It only looks tidy, as most of the stuff that was on the whole back wall, is now in the trailer to go to the tip, or has been shoved in my 2.2x2.4m "Spare parts room", and now I can't get to anything in there Ha ha ha I could definitely do with a bit more space, but I'd just end up with your problems I'm going to enclose the car port beside the garage, and move a lot of stuff into it I think. OR... It will be setup as a fabrication area, and the main garage will have parts storage in it. I'm not sure yet... Need some pictures of that big shed you've got with the bikes and Skyline in
    • No. I think it's gone. 😭 I think you can get body coloured ones on eBay so I think I'll get one of those... Or just hang a red ribbon from the hole and whack a TOW sticker next to it.
    • Can't say I've had a bad experience with one on my car, then again it only gets washed once or twice a year... The wheels on the other hand, get a good spray often due to my shitty dusty pads.
    • @MBS206 thats pretty neat and tidy to me!  I'll get a photo of mine when I'm out there next. It might require multiple photos to understand the scale of the atrocities though... In total I have 4 sheds of varying sizes and layouts. Main shed is 14x8, second shed is 3x8, third shed is 11x2.5, fourth shed is around 6x4.  All are pretty much full.   The main goal of my cleaning tsunami is to make the main shed predominantly car and motorbikes only. Second shed is my metal fab room (2 x bench grinders, drill press, bench belt sander, metal band saw, scrap metal storage and some of my garden tools.  3rd shed is more bigger garden stuff, storage for engine crane, jack stands, concrete grinder, concrete mixer, air compressor lives there, and it now has two 2mx2m pallet racking shelves with itemised boxes holding building stuff, electrical stuff, plumbing stuff, etc, etc.  The 4th shed is Ryobi electric ride on mower, mini boom sprayer, ancient Kubota tractor, more garden stuff!  I have got a lot of shit....  Then there's the pool house (8mx4m) and the pool pump shed (4mx4m).  I built all of the sheds over the 11 years we've been here.  The main shed was a Ranbuild kit, the rest are all custom made to fit the areas available. Building the main shed taught me a LOT as I had no idea about building anything prior to that!  I've still got one more in me. It will be my man cave which I poured the extra concrete for way back when I poured the concrete for the main shed. The idea is the Skyline will be a centre piece of the main cave once (if...) it's finished.  I told my now 14 year old son yesterday that I will 100% drive him to his year 10 formal in 2 years. Still a long way off but at least I now have a date to work towards! 🤣
    • Modern oils are amazing. Add tyres to that as well.
×
×
  • Create New...