Jump to content
SAU Community

Recommended Posts

Sorry to Hi-jack your thread but does anyone know with "street semi's" like Federal RSR's for example is there any point in warming them up at the drags or are they the same as normal street tyres that don't like heat?

Sorry to Hi-jack your thread but does anyone know with "street semi's" like Federal RSR's for example is there any point in warming them up at the drags or are they the same as normal street tyres that don't like heat?

its always good to warm up the tyres this will give you bit of extra grip , you probably seen other cars running semi or even full slick still warming them up.

its always good to warm up the tyres this will give you bit of extra grip , you probably seen other cars running semi or even full slick still warming them up.

I under stand the guys with race tyres warming them up coz race tyres only work at a certain operating temp's but street tyres are designed not to need to be warmed up to be able to produce grip & iv been told heating them can actually make things worst. So just wondering how these street semi's work.

It comes down to how much power your car is putting down and how serious you are.

Do you have a 185kw, FMIC, exhaust, filter car or a 300kw, GT3076 + supporting mods car or a 350+, forged, gt35 + all the fruit car?

If it's 185, a warm up is pointless, traction won't be an issue. If it's ~300ish then it might be of use you're running street tyres, but in reality you'll do better simply managing your throttle and clutch better. If it's the last option, then I would expect you are running slicks and intend on launching hard and a warm up burn out is definitely beneficial (if not slicks then no amount of street tyre burnout is going to stop you wheel spinning for a good portion of the race).

So, in conclusion, I'm going to bet your running moderate power on street tyres which means a pre race burnout is going to give very limited benefit. But do one anyway, cause they are fun :)

I under stand the guys with race tyres warming them up coz race tyres only work at a certain operating temp's but street tyres are designed not to need to be warmed up to be able to produce grip & iv been told heating them can actually make things worst. So just wondering how these street semi's work.

pretty sure the tyres will be warming up regardless, when doing a burn out you give the tyre the chance to grip the surface properly when taking off i own MT semi slick tyres and yes they are meant to be warmed up , those that dont properly dont have the option to, however from experience , it works.

Edited by Hiroshima Screamer

It comes down to how much power your car is putting down and how serious you are.

Do you have a 185kw, FMIC, exhaust, filter car or a 300kw, GT3076 + supporting mods car or a 350+, forged, gt35 + all the fruit car?

If it's 185, a warm up is pointless, traction won't be an issue. If it's ~300ish then it might be of use you're running street tyres, but in reality you'll do better simply managing your throttle and clutch better. If it's the last option, then I would expect you are running slicks and intend on launching hard and a warm up burn out is definitely beneficial (if not slicks then no amount of street tyre burnout is going to stop you wheel spinning for a good portion of the race).

So, in conclusion, I'm going to bet your running moderate power on street tyres which means a pre race burnout is going to give very limited benefit. But do one anyway, cause they are fun :)

you haven't been to the drags much have you? i was having traction issues with about 180hp (so about 135kw) in my magna. a mate of mine had a sr20 in a sigma and with street slicks he was lifting one of the front wheels off the ground when launching and he only had about 250hp. he was simply holding it on the rev limiter and pretty much just side stepping the clutch. his 60' times were around 1.5 seconds.

you haven't been to the drags much have you? i was having traction issues with about 180hp (so about 135kw) in my magna. a mate of mine had a sr20 in a sigma and with street slicks he was lifting one of the front wheels off the ground when launching and he only had about 250hp. he was simply holding it on the rev limiter and pretty much just side stepping the clutch. his 60' times were around 1.5 seconds.

Actually, I have.

My 33 was a typical 11psi, FMIC, exhaust and pretty healthy. I had china specials on the back and traction was never an issue. I could light up the rears in first and a tiny chip/squirm into second if I wanted, but by christ I had to be pumping it pretty friggin' hard. Pull back to 95%, which is sensible if it's your daily, and traction was not an issue.

It comes down to how much power your car is putting down and how serious you are. Do you have a 185kw, FMIC, exhaust, filter car or a 300kw, GT3076 + supporting mods car or a 350+, forged, gt35 + all the fruit car? If it's 185, a warm up is pointless, traction won't be an issue. If it's ~300ish then it might be of use you're running street tyres, but in reality you'll do better simply managing your throttle and clutch better. If it's the last option, then I would expect you are running slicks and intend on launching hard and a warm up burn out is definitely beneficial (if not slicks then no amount of street tyre burnout is going to stop you wheel spinning for a good portion of the race). So, in conclusion, I'm going to bet your running moderate power on street tyres which means a pre race burnout is going to give very limited benefit. But do one anyway, cause they are fun :)

I dono my R34 was only making 165rwkw & i was having some pretty big traction issue. Had to baby it off the line (holding it at about 3 grand, slowly stepping off the clutch & waiting before I went to WOT) otherwise I went no where just spun.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’d love to find some where that can recover the dashes to look brand new and original. Mine has a very slight bubble, nothing compared to some I’ve seen though 
    • $170K. I asked one of the guys there as a joke if that price was just for the passenger seat as it was where the price sheet was... he tried really hard to crack a smile 😄 He also mentioned that every single part of the car was inspected and either restored or replaced with a new or as new part, or made from scratch. The interior was incredible, every inch like a new car.
    • Time for a modernisation, throw out the AFM, stock O2s, ECU into the e-waste bin. Rip out the cable throttle, IACV, pedal, etc. into the scrap metal bin. DBW, e-throttle, modern ECU, CANbus wideband, and the thing will drive better than when it left the factory.
    • I agree, don't go trusting those trims. As I said, first step is to put the logger away, and do the basics in diagnosis.   I spend plenty of time with data loggers. I also spend plenty of time teaching "technicians" why they need to stop using their data loggers, and learn real diagnostics.   The amount of data logs I play with would probably blow most people away. I don't just use it to diagnose. I log raw CAN data too, as a nice chunk of my job is reverse engineering what automotive manufacturers are doing.
    • I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
×
×
  • Create New...