Jump to content
SAU Community

Where To Buy Naggy Little Parts?

K4L4M1TY

By K4L4M1TY,
in General Maintenance

 Share

Recommended Posts

K4L4M1TY Contributor

K4L4M1TY

Posted
Posted (edited)

Just wondering where people from NSW go for small parts like bolts, nuts, interior bits and pieces, mainly the things that are Nissan only or GTR parts new or used?

I ask because i'm needing to buy a clutch vacuum check valve, which after identifying I am not sure if I will have to go to Nissan for things like this if they even still have/make them or what my options are in this situation. I've been to Just Jap and their stock didn't seem quite sufficient for what i'm looking for in a parts supplier (i'm sure they could probably get anything we need though). Any advice would be greatly appreciated guys.

EDIT: Could i get parts through my local Nissan service department for an 89 GTR?

Edited by K4L4M1TY
Link to comment
https://www.sau.com.au/forums/topic/401884-where-to-buy-naggy-little-parts/
Share on other sites
gtr jet Veteran

gtr jet

Posted
Posted

Some more generic things you'll be able to pick up from Burson's but Nissan do also stock a lot of skyline parts. Some stuff will have have to ordered from japan though. Just go down to Nissan parts and see what they can do.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      I've uploaded logs / the current map to Gdrive if anyone has any ideas. https://drive.google.com/drive/folders/1FPnr22Z-EilG7tYdHSi0Qb07P2jfFLKV?usp=sharing
    • luke gtr
      Spotted on the street....

      By luke gtr · Posted

    • MidnightR32
      RB20DET lean on cold start

      By MidnightR32 · Posted

      I'm running a Haltech Platinum Pro with the stock map for the RB20DET + tweaks for my build. When I started it this morning, the IAT was at 32F/0C (Outside temp was ~42F) and the AFRs went off the scale for my AEM gauge. I let it run for ~30 seconds then turned it off. I then did a smoke test, by hooking into a vacuum line directly behind the throttle body, and confirmed there was no leaks ( i let the smoke tester run for ~5 minutes / confirmed it was generating smoke before hand ). I then started the car again, after fixing a power steering leak.... and it seemed to be happy for ~30 seconds (was at ~11/12), but then seemingly shot back up to ~18 again. I then let the car run for a few minutes, thinking this was just cold start related, but the AFRs never came back down. I didn't let the car fully warm up, so maybe this makes sense, but I'm not sure what to do? The AFRs, when I last ran it, were normal, but because of personal reasons I haven't been able to break in the car. It was rebuilt last year. Engine / Mod list: Supertec pistons Spool rods Kelford 270 cams and Springs Stock crank Deatschwerks 900cc injectors Walbro 255 (Wired directly to the battery relocated in the trunk) NKG Audi R8 Coil packs + Conversion Harnesses from Wiring Specialties Holset HY35 turbo Haltech Platinum Pro ECU Haltech boost controller (wired in for high boost RB25 Neo transmission + needed bits for the speedo to work  
    • luke gtr
      Spotted on the street....

      By luke gtr · Posted

      Not great at getting the camera out fast enough for cars driving. Even in traffic. S15 is in front of the kei truck.
    • luke gtr
      Spotted on the street....

      By luke gtr · Posted

      Most will be parked.
×
×
  • Create New...