Jump to content
SAU Community

Recommended Posts

Hi All,

In the last couple of weeks and mainly since our cold Melbourne mornings I'm getting the hand brake dash light staying on in my R33.

Sometimes the light will turn off immediately after the hand brake is released then will turn on again after several seconds, but mostly it will remain on until the engine has been running for 10-15 minutes. For the rest of the day it will continue indicating correctly.

Now i'm wondering if this light might be used to indicate any other car related issues? I do have a power fc but as far as im aware it only uses the engine light for sensor maxing and the rest of the warning lights should act as they did with the OEM ECU.

The car doesn't appear to be driving any different than normal, and it may very well be just a faulting switch on the hand brake. But this starts to seem unlikely when as mentioned early sometimes it does go off as it should then turns on again (without touching the hand brake)

Any help would be very appreciated.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/402319-hand-brake-light-staying-on/
Share on other sites

it also indicates low brake fluid, which can also be an indication that your brake pads are low. check the brake fluid level. if it's low then also check your brake pads, because the lower the pads get, the more fluid is in the calipers and less in the reseviour. if the pads are low then only put a small amount of brake fluid in to get the light to go away, otherwise when you put new pads in you may end up with brake fluid overflowing when you force the pistons back into the caliper

it also indicates low brake fluid, which can also be an indication that your brake pads are low. check the brake fluid level. if it's low then also check your brake pads, because the lower the pads get, the more fluid is in the calipers and less in the reseviour. if the pads are low then only put a small amount of brake fluid in to get the light to go away, otherwise when you put new pads in you may end up with brake fluid overflowing when you force the pistons back into the caliper

Yeah check this

I got caught out searching for a dodgy wire, ripped my seat out and started pulling the floor carpet up and checking the wiring. Then checked the fluid and it was low. Topped it up and light went away. I found my light went out under braking sometimes

Thanks guys, I did wonder when I was in the car the other day if it might also relate to the main braking system.

I tried pumping the brake to see if more pressure made any difference to the warning, but no dice.

The reservoir is below max but still within the indicated min mark. Will give a little bit of a top up and check out how the brake pads are fairing tomorrow. Certainly still have a firm pedal feel so hopefully its just being over sensitive to the reservoir level.

Thanks again and hopefully I'll have good news to report soon.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all. I am aware there is lots of discussions about jacking points, where to lift the car and what not. But as usual just a lot of "in my opinion" and nothing definitive, and everyone does it in a different way. I want to hear from some experienced people on which points on the car it's okay/safe/recommended to lift the car using a four point hoist/lift. I will attach some images of my underbody. Sills are largely okayish, the driver side jacking point is pretty mangled though and it looks like the underfloor is slightly pushed in too, but I might be wrong. In the German Skyline forum, the consensus is to use the sidemember chassis rails in the front and the rear subframe? bushing in the rear. I know the manual says to never use the sidemember for loading but lots of folk do it and it was definitely done on my car too as they are slightly bent too. Based on the images, what points do I use to not make the already present damage worse? I'd use wood or rubber blocks to spread the load across a bigger area of course. Driver side sidemember and jacking point mangled one) https://imgur.com/a/eKjzrJX Driver side rear jacking point https://imgur.com/a/W3DWF1P Passenger side sidemember and jacking point https://imgur.com/a/65UvIJe Passenger side rear jacking point https://imgur.com/a/h3k7j53 We can also see some underbody rust but so far it all looks somewhat treatable and nothing that requires a Yoshida style restoration.
    • Have you put an aftermarket oil pressure gauge on and verified your oil pressure?   Noise being on the block, on exhaust side, how high up the block does it seem to be? It could be the VCT system getting cranky, especially if it's mainly at idle, and when warm, as that'll be your lowest point for oil pressure. Could be showing that oil passages / VCT solenoid are blocking.
    • Well, hydraulic lifters will get noisy if they are dirty/fouled in some way, and exactly how that manifests will depend on exactly what schmutz is where. There is a procedure on here somewhere for dismantling and soaking/cleaning them. Replacing them with new is about 50% of the work and about 5% of the money!
    • Thanks for the reply @GTSBoy this is is a hydraulic lifter engine. Yea right i did not realise the lifters were supposed to be compressible while installed. I could push them down but i had to lean almost my while body weight on them.  I have never heard of a lifter/ lifters ticking only at hot idle and getting worse the hotter it gets. I have owned a few jdm cars with noisy lifters. This noise is slightly more subtle, it is more of a sharp gentle metalic tic than the solid and more loud tapping I've heard on lifters. I have used a metal rod, alloy tube, hose and stethoscope and could not find the source of the tick. But it appears to be loudest on the actual engine block behind the exhaust cam gear and next to the oil filter. I had mate (40 year old mechanic) go over it with me and he couldn't find it either..  Could it be a cam seal issue of some sort?  Cheers  
×
×
  • Create New...