Jump to content
SAU Community

Rb30 Patrol Efi Conversion

showtime393
 Share

Recommended Posts

showtime393 Rookie

showtime393

Posted
Posted (edited)

Hi all.

In the final stages of my efi conversion on my Nissan patrol.

Having some hassels with wiring. I am able to get 12v to my coil. But getting no spark past my coil.

I have put computer into diagnosis mode and are getting back the following codes.

Code14 vehicle speed sensor

Code 22 fuel pump circuit (using a seperate solinoid set up)

Code 24 neutral park switch ( manual computer)

Code 31 heater/ac

Code 32 starter signal circuit

Would any of these faults prevent me from getting spark?

I was thinking it could be the starter signal circuit, I have located this wire in the loom, but I am unsure where to get a starter signal from. I was thinking putting accessories 12v to it. But given that it's a black with white trace wire. I have decided not to try this.

Was hoping to get some advice and thought here would be a good place to start.

Thanks Cam

Edited by showtime393
Link to comment
Share on other sites
steve200b Proficient

steve200b

Posted
Posted

Hi

I have done Agnew of these and the only problem I have had is the ignition source needs to come from the old coil wire as the others don't have power when cranking. Double check the pinouts on the ecu.

Good luck you should be wrapped with the result.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Beanie
      Hello from the UK

      By Beanie · Posted

      Well I had 2 choices from then on. I either had to (reluctantly) move it on to another potential buyer and take the loss on the chin. Or I stick with it and turn it into a restoration project. I chose the latter. Project Snowstorm began! The frp body kit was the first thing to go. Turns out the original colour used to be silver. The Neo and gearbox were removed, along with the prop and exhaust system before it took a trip to the bodyshop, where I wouldn’t see it again for quite some time due to the pandemic hitting very soon after they took it away. Eventually, progress began and damage assessments made. Even the front chassis leg was in pretty bad shape!     Then the chopping commenced. For these guys it was just usual routine, to me it looked absolutely terrifying!   More to follow as I’m struggling to focus on my screen at 12:45 am!!!
    • TurboTapin
      CD009 RB Conversion

      By TurboTapin · Posted

      That's the most absurd thing I've ever heard. I would go cut bellhousing over that monstrosity of a flywheel all day, every day. It puts a lot more mass further from the last main bearing. I've had nothing but problems with Collins in the past and refuse to ever buy their products again. I would not trust anything they tell you. He's playing his salesman card.  I'm currently at 640whp on a mustang dyno (~770bhp) with the intentions of running E85 and a lot more power this upcoming spring. Cheers, 
    • GTSBoy
      PRP RB26 cast block + head prototype running

      By GTSBoy · Posted

      Nah, it's not the reduced knock margin. It is a direct mechanical effect of having to initiate the combustion earlier, while the piston is still rising, which starts to exert combustion pressure on the rising piston earlier, making the rest of the engine work harder to finish driving the piston up to TDC where the combustion pressure stops being a negative and starts being a positive. Your modern engine that only needs ~10° to make MBT doesn't waste the other 10 or so degrees of crank rotation. That's almost all of it. The difference in knock margin might go either way. Remember that modern engines to which you are currently comparing the long tractor engine (the RB) are now running super high compression, direct injection, tricky cam control and maybe even cylinder pressure sensors. You're not comparing apples with other fruit. It's apples and sea weed, or some other evolutionarily primitive vegetation. And remember, squish only really comes into play at the very end of the stroke. It certainly does good things, but it is not the biggest contributor to what's going on. It is quite possibly much less important in 4 valve head than 2 valvers also, because there is so much less squish available to a 4 valve anyway.
    • Dose Pipe Sutututu
      PRP RB26 cast block + head prototype running

      By Dose Pipe Sutututu · Posted

      Food for thought, a longer stroke motor would need less ignition timing vs. a shorter stroke motor requiring more ignition timing.
    • PranK
      Skid pans in/around Sydney?

      By PranK · Posted

      Thanks Duncan, HART is only 10 mins from me (I did my bike license there), it'd be awesome if it ran these types of things.  Sutton Road does look good and they take fewer cars than SMSP which is good.  Surely you have enough land to lay a few million tonnes of concrete and some sprinklers D? 
×
×
  • Create New...