Jump to content
SAU Community

Recommended Posts

You pair have nothing

You want a long cruise head out through cessnock to broke then take Charlie's road across to putty rd the head out the golden hwy to sandy hollow and turn onto Bylong Valkey way which goes back to Richmond then a short hop to Windsor and back up putty road to singleton and home

that doesnt look too bad, but looks to actually be a shorter route!

The Putty run we did a few years back was a long day, we did Old Pac, Galston Gorge, Windsor and then Putty Rd through to Singleton..... It was a 2 fuel stop trip on that run..... On that note, how far is that drive in KM? And have you mapped out fuel stops? (Taking into account that ill only make <300kms to a tank lol

ful trip is 650kms... you would have to see where to get your fuel from.

I will bring a spare bottom end, ill have to change that out when u guys fix what u break :ph34r:

Good plan! Anyone got a 2 poster they can bring?

that doesnt look too bad, but looks to actually be a shorter route!

ful trip is 650kms... you would have to see where to get your fuel from.

I fuelled up in Sydney and then again in Singleton on our run.....

But my flex fuel is back on now so i can run whatever, not an issue :) Just have to run low boost with normal pump fuel :( Only 19psi lol

may need to plan this one for winter so its easier on the cars haha..

Yeah plus cooler = more wasps! And if the car bursts into flames we can all sit around the campfire and inhale the E85 goodness!

so the bad news for this week. according to my mechanic my crank shaft is f*cked an my easiest and cheapest way out is an engine swap. honestly i hate my life.

anyone know of any dirt cheap r33 rb25de motors kicking around?

so the bad news for this week. according to my mechanic my crank shaft is f*cked an my easiest and cheapest way out is an engine swap. honestly i hate my life.

anyone know of any dirt cheap r33 rb25de motors kicking around?

Is the head still good?

If its a DE as you say then any VL bottom end with a light hone, new rings and bearings and your head fitted should do nicely

You need to fit an idler pulley for the belt return and I think that's it

Best bet is to do a search on here as there is a heap of info around just have to find it

As far as legalities go I'm not sure but if original engine number then no capacity increase

so the bad news for this week. according to my mechanic my crank shaft is f*cked an my easiest and cheapest way out is an engine swap. honestly i hate my life.

anyone know of any dirt cheap r33 rb25de motors kicking around?

Sell car and get a PULSAR VZ-R N1. Iron chef has one up for sale. SR16VE N1 Engine.... stock 200hp, 1090kg and 6.8 secs 0-100

Put on a full exhaust, apexi power FC, splitfire super direct ignition,etc and youll have around 300hp at the flywheel and 0-100 in 5 second territory.

Sell car and get a PULSAR VZ-R N1. Iron chef has one up for sale. SR16VE N1 Engine.... stock 200hp, 1090kg and 6.8 secs 0-100

Put on a full exhaust, apexi power FC, splitfire super direct ignition,etc and youll have around 300hp at the flywheel and 0-100 in 5 second territory.

Face palm :no:

f**k that sucks man. wonder how much it'll cost to how much you could sell it for.

N/A engines should be cheap and pretty easy to get ahold of man!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • It only looks tidy, as most of the stuff that was on the whole back wall, is now in the trailer to go to the tip, or has been shoved in my 2.2x2.4m "Spare parts room", and now I can't get to anything in there Ha ha ha I could definitely do with a bit more space, but I'd just end up with your problems I'm going to enclose the car port beside the garage, and move a lot of stuff into it I think. OR... It will be setup as a fabrication area, and the main garage will have parts storage in it. I'm not sure yet... Need some pictures of that big shed you've got with the bikes and Skyline in
    • No. I think it's gone. 😭 I think you can get body coloured ones on eBay so I think I'll get one of those... Or just hang a red ribbon from the hole and whack a TOW sticker next to it.
    • Can't say I've had a bad experience with one on my car, then again it only gets washed once or twice a year... The wheels on the other hand, get a good spray often due to my shitty dusty pads.
    • @MBS206 thats pretty neat and tidy to me!  I'll get a photo of mine when I'm out there next. It might require multiple photos to understand the scale of the atrocities though... In total I have 4 sheds of varying sizes and layouts. Main shed is 14x8, second shed is 3x8, third shed is 11x2.5, fourth shed is around 6x4.  All are pretty much full.   The main goal of my cleaning tsunami is to make the main shed predominantly car and motorbikes only. Second shed is my metal fab room (2 x bench grinders, drill press, bench belt sander, metal band saw, scrap metal storage and some of my garden tools.  3rd shed is more bigger garden stuff, storage for engine crane, jack stands, concrete grinder, concrete mixer, air compressor lives there, and it now has two 2mx2m pallet racking shelves with itemised boxes holding building stuff, electrical stuff, plumbing stuff, etc, etc.  The 4th shed is Ryobi electric ride on mower, mini boom sprayer, ancient Kubota tractor, more garden stuff!  I have got a lot of shit....  Then there's the pool house (8mx4m) and the pool pump shed (4mx4m).  I built all of the sheds over the 11 years we've been here.  The main shed was a Ranbuild kit, the rest are all custom made to fit the areas available. Building the main shed taught me a LOT as I had no idea about building anything prior to that!  I've still got one more in me. It will be my man cave which I poured the extra concrete for way back when I poured the concrete for the main shed. The idea is the Skyline will be a centre piece of the main cave once (if...) it's finished.  I told my now 14 year old son yesterday that I will 100% drive him to his year 10 formal in 2 years. Still a long way off but at least I now have a date to work towards! 🤣
    • Modern oils are amazing. Add tyres to that as well.
×
×
  • Create New...