Jump to content
SAU Community

R33 Gtr Parts Wanted

mdillonmining

By mdillonmining,
in Wanted to Buy

 Share

Recommended Posts

mdillonmining Contributor

mdillonmining

Posted
Posted

I'm chasing the following R33 GTR parts

Main things i need straight away are the tailshaft and gearbox crossmember and speedo sender I fitted a gtr box on my r33 will drive it 2wheel until I can get all the other parts and enable 4wd

r33 gtr tailshaft and prop shaft,

gearbox crossmember

r33-r34 gtr/gts4 speedo sender

r33 gtr engine cross member + lower control arms + front sway

front hubs

front drive shafts

gtr sump

R33-34

attessa pump

abs unit

abs electric controller

attessa controller

rear diff

pm or reply for any of these bits and peices with a price

I'm located on the gold coast and can pickup within a 300km radius or organise frieght/post depending on the size of the item

Link to comment
https://www.sau.com.au/forums/topic/402601-r33-gtr-parts-wanted/
Share on other sites
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

You can't mix and match. R33 and R34 are very different - dfifferent Atessas and different diff ratios ...R33 are 4.1 and R34 are 3.545:1 so you will also need speedo sende to match your diff ratio.

Good luck with your project!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Lithium
      R32 GTS-t RB30 sedan

      By Lithium · Posted

      To be fair passengers who aren't silly and have been in proper fast cars have often been pretty impressed once you hit 4th gear   
    • Lithium
      HKS stroker kit step 0/1 or HKS GTIII 2530

      By Lithium · Posted

      Outstanding!
    • BaronOBeefdip
      Baron's R34 GT-R build thread - car in Japan for 5 years -_-

      By BaronOBeefdip · Posted

      I suppose that's true. Barring almost any situation, I'll never sell so what the market does is kind of irrelevant to me. It's possible I'd make most of my money back. That spreadsheet I mentioned? Maybe I could make back more than what the car's total costs thus far are, but the parts and all that is possibly a different story... Thanks for reading. It was certainly a good moment and just makes the ties to the car that much stronger. It's exciting that the option will be there to bring it over, however I have some plans with a shop that may end up keeping the car there longer, not sure. Coupled with the fact I want to move there and haven't solidified any path yet. So in a way, it feels like I'm in a limbo state that is uncertain; time will tell.
    • TurboTapin
      HKS stroker kit step 0/1 or HKS GTIII 2530

      By TurboTapin · Posted

      No worries, everything worked out in the end. I just wanted to make the point that it doesn't matter where it comes from (I.E Australia), it can be broken or improperly built. I would still purchase from these companies in the future. B2R - Not certain how that finished, this was on a car I wired a few things and street tuned. I know the owner ended up shipping the motor back to Australia for investigation. Hopefully some of it is covered under warranty.  Turbosmart - I always pressure test everything that goes on my car. It's a habit from my career in oil and gas. I run two 40mm's and both had major leaks from the actuator to exhaust portion through the shaft. I returned both, they shipped me back two and one was leaking and the other had a 38mm top (40mm gate with 38mm actuator cap, no idea how that happens). Eventually after a lot of back and forth I found myself with two non-leaking gates. I believe this happens a lot more then people would like to believe but you would never know if you don't pressure test them prior to installation. Crank Motorsport - Issued a full refund and let me keep the seat rails. I turned them into scrap metal for other projects. GKTech - Shipped me out a replacement and asked that I modify it as per my idea and that they would do the same for a future revision. ATP - Can just needed a large shim to bolt up properly.  Haltech - They started an actual proper Beta channel for firmware's a few months back and stopped using the general public for testing. I'm now much happier.  Speedtek - f**k Speedtek. I would love to watch them burn.     
    • Murray_Calavera
      HKS stroker kit step 0/1 or HKS GTIII 2530

      By Murray_Calavera · Posted

      I've got a Turbosmart wastegate, ATP catch can, many GK Tech parts and Haltech everything. Everything's been perfect, sorry to hear your experience wasn't the same
×
×
  • Create New...