Jump to content
SAU Community

R33 Rear Seat Belt Wont Retract

AJ33

By AJ33,
in General Maintenance

 Share

Recommended Posts

AJ33 Rookie

AJ33

Posted
Posted

Hi Guys,

The left hand side rear seat belt is pulled out all the way and wont retract, does any one know what i need to do to be able to get to the assembly mechanism. i am thinking that the whole of the back seat needs to come out? am i heading in the right direction with this. Any help would be greatly appreciated.

The car is a 96 r33 gtst series 2

Thanks

Link to comment
Share on other sites
Ty1 Experienced

Ty1

Posted
Posted

hey mate yea the back seat needs to fully come out. I've done this many a time now. once the seat is out you should be able to see the seatbelt retractor unit.

Link to comment
Share on other sites
AJ33 Rookie

AJ33

Posted
  • Author
Posted

Thanks for that Ty, did as you mentioned and now its all good. Once i could get to it, just sprayed a bit of WD on to it that was enough to get it spinning again.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
    • alexburns
      Interior Light Problems

      By alexburns · Posted

      @99RS4just wondering if you ever took photos of the footwell lighting / how you bypassed the controller, im keen to haver footwell lighting come on when I open the doors too   
×
×
  • Create New...