Jump to content
SAU Community

Recommended Posts

Hey Peeps I have a bunch of R33 parts up for grabs,

I have for sale my Hypergear ATR28 G2 Highflow (R33) Turbo, no shaft play, only used for around 8000km's. Has made 235 rwkw @ 18psi on my R33 GTST with almost stock response.

Comes with HKS Adjustable Actuator (Set to 15psi), and braided oil line.

I also have a 3" JJR Bellmouth Dump/Front Pipe and Apexi Super Suction Kit Intake pipe (2.25" - 3.5")

The dump pipe has a O2 sensor attached (8000kms old) that I will throw in.

I will sell all 3 peices as a kit (Turbo, Dump and Intake) for $850

This will give you all you need for a good free flowing setup.

Or as single peices:

Turbo and HKS Actuator $700

Dump Pipe $100

Apexi Intake Pipe $150 These Intake kits are over 400 bux new

538-n011_copy_2.jpgjjrdumpfrontrb.jpg

102_8715.jpg

I will post up pics of the turbo with actuator tomorrow night

I also have Powdercoated RB25 Plenum and Crossover Pipe coated by Craved Coatings (SAU Member) Those of you that know Chris know how good his work is. They are coated in silver chrome to give them a polished look without the constant cleaning needed on polished parts. All cast marks have been removed and entirely smoothed out.

I am after $300 for both and I will throw in the BOV (Standard RB25) as it is still attached to the crosover pipe.

102_8713.jpg

102_8712.jpg

102_8726.jpg

102_8727.jpg

I also have a full R33 GTST S2 interior, Front Seats, Rear seats, Front Door Cards and Rear Cards up for grabs.

Drivers seat stitching is starting to come undone in the usual spot but not bad (will post up a detailed pic tomorrow) and front doors cards have a small hole in each for tweeters but generally in very good condition.

$400 for the whole lot.

IMG_0170.jpg

IMG_0168.jpg

All parts are in Hills area Sydney, will post at buyers expense but would prefer local pick up for the interior.

Pm me if you are interested and Ill get back to you ASAP.

Cheers

I'm also from the hills, I swear i've seen your car around! Now i know how immaculate it looks under the bonnet!

Will keep an eye out for you / any more parts that come up that i'd be intersted in.

:wave::thumbsup:

You probably have Colin, I have owned it for over 10 years.

The pics posted on here are the old setup, looks even better now :)

That's why I'm selling all this stuff, need to pay for more go fast bits

JJR Dump pipe sold - Thanks Matt

Apexi intake pipe back up for sale - wasn't what buyer was after

Powdercoated plenum and crossover pipe with bov still for sale

R33 series 2 full interior still for sale

Turbo and Intake sold

Still have powdercoated Plenum, Crossover Pipe and BOV up for sale as well as Series 2 Interior.

Come on peeps, buy my Sh1T! Nothing wrong with a bit of bling

  • 9 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah 4wd (boosted) has a recess in the firewall for the booster, and 2wd is flat - the example in the link shows the flat surface. When you deleted the booster, did you just attach the factory slave cylinder directly to the recess in the firewall with no adaption?  
    • Yes, but no. You need to keep the mating surfaces bare (ie the flat faces where the caliper and upright pads touch the dogbone) and also the internal threads will remain bare (unless there are no internal threads - do they use nuts on all the bolts?). So you can slow down obvious external corrosion, but not all of it. Anodising would be required to provide decent protection to the alloy, but I'm not actually sure if you should anodise something that is all about the strength. Anodising does reduce strength significantly. Like, up to 50% on some alloys for high thickness coating.
    • Thanks   does painting on aluminium work or stop them from corroding?
    • 'Sgot nothing to do with them being Japanese. The climate in the north of Japan has similarities to the UK - the cars are made in the knowledge that they have snow and salt, and they rot there. Cars made in the US rot like buggery in the US. British cars have always rotted regardless of the weather. They will rot indoors in a climate controlled bubble! The brackets are not unsafe yet, but they will get that way. They may well corrode where the bolt threads are in contact and the bolts could just jump out without warning.
    • So unsafe would you say now?   little bit of has come off, guess road salt is a nightmare for Japanese car. Mx5 here have a well known issue or rotting 
×
×
  • Create New...