Jump to content
SAU Community

M35 Attesa Ets "pressure Switch" Problems

slippylotion
 Share

Recommended Posts

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Erop
Erop

you may be interested - in cold Russia the most suspicious part of ATTESSA is used to be the pressure control switch, which causes C1208 error reading this is one of this crap pieces it's not

Erop
Erop

this switch is only marked with PS-20 the WAKO doesn't sell less than 1000 pcs now looking for byuing this switch, still no exact code, Scott's right BUT - you may take it from R32-R34, Laurels,

Posted Images

slippylotion Mentor

slippylotion

Posted
  • Author
Posted (edited)

Well I got a call back toady after the pump assembly was tested and it's f@cked. The pressure switch and accumulator are shagged and the motor itself is chewed out with the impeller chewing on the inner casing all due to the pressure switch sticking on.

So I'm getting a change over reconditioned assembly ex Japan for $1920 to my door from Hills Motorsport. The new pump is the late updated model with a better pump design and Pre filters fitted. Only catch is its a 30 day wait from Japan then for Hills to bech check and set it up then post to me, I'm expecting to wait about 6 weeks until I can refit it. Still could have been worse as its the last ready unit on the shelf.

Edited by slippylotion
scotty nm35 Grand Master

scotty nm35

Posted
Posted

Well I got a call back toady after the pump assembly was tested and it's f@cked. The pressure switch and accumulator are shagged and the motor itself is chewed out with the impeller chewing on the inner casing all due to the pressure switch sticking on.

So I'm getting a change over reconditioned assembly ex Japan for $1920 to my door from Hills Motorsport. The new pump is the late updated model with a better pump design and Pre filters fitted. Only catch is its a 30 day wait from Japan then for Hills to bech check and set it up then post to me, I'm expecting to wait about 6 weeks until I can refit it. Still could have been worse as its the last ready unit on the shelf.

I might have a spare assembly soon, not sure on the condition yet. That sounds like an expensive rebuild to me...

slippylotion Mentor

slippylotion

Posted
  • Author
Posted

I wouldn't say its expensive seeing as the accumulator is around $350 trade price alone and about $200 for a pressure switch that you can't actually buy from Nissan then the cost of a new pump that again you can't buy separate from Nissan and I need the complete assembly. Nissan only sell the complete pump assembly for $5k trade. New pump assembly in Japan is around 200,000yen from Nissan. These are rebuilt in Japan but with Australian warranty from Hills Motorsport. Im not keen to take the chance on a s/hand pump as it could go a week later. Atleast with this I have a warranty and shouldn't have any further problems for the 5 ish years Ill keep the car.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Im not keen to take the chance on a s/hand pump as it could go a week later. Atleast with this I have a warranty and shouldn't have any further problems for the 5 ish years Ill keep the car.

Yep, I agree it would usually be the best option but at that price? Its not like everyone else is replacing them, they are quite reliable in most cases. It's you coin buddy...

slippylotion Mentor

slippylotion

Posted
  • Author
Posted

Yeah I agree its a lot of coin but it seems the cheapest way to fix it correctly and completely. I though of a second hand unit but they sell for $700-900 so if it dies in a year or two its really half the cost of the fully rebuilt assembly wasted seeing as a new unit should last another 10 years or so.

Id probably guess that the other guys getting the pressure switch fault code or 4WD randomly coming on are probably in the same boat. I asked why my torque gauge would still read if the pumps shagged and he said its a theoretical reading via the G sensor not the actual pump pressure. While the gauge is showing front drive it may well not be actually getting it.

zei20l Grand Master

zei20l

Posted
Posted

$700-900 for 2nd hand? massive rip off

i have a complete unit here you can have for $150. no idea if/what is wrong with it. but it might be a hell of a lot cheaper to pull bits off than 2k for a 'new' one

slippylotion Mentor

slippylotion

Posted
  • Author
Posted (edited)

Thats cheap. Theres one on Yahoo at 25000 yen so far then postage and fees it will be around $400-500.

I know $1900 seems like a lot but I don't want to have another problem with it again while I have the car. I suppose its similar to replacing a turbo with a cheap stock unit, bound to go at anytime so might as well just go a new one.

I also just double checked the oil I bled out of it last week while flushing some through and found all the little metal fillings in it. Just a bummer all 3 parts of my pump assembly died :angry:

Edited by slippylotion
  • 1 month later...
Sage222 Rising Star

Sage222

Posted
Posted

any more news on this one guys? i am wondering if my attessa has the same problem :( i have the same dashboard dimming and the front torque guage blip issue when the 4WD light is off.. when the 4WD light is on all is smooth.

though i think ill remove shafts and disable the pump rather than spend a heap of coin on fixing it..

ironpaw Veteran

ironpaw

Posted
Posted

nothing? :(

I had this issue...4WD light coming on intermittently, the ATTESSA pump chirping away...

I had a dead battery a month ago and replaced the battery, left the battery unplugged for a week.

Started driving again last Wed and haven't seen the 4WD light on yet...so not sure wtf the problem is...pump hasn't been chirping like mad either...

ironpaw Veteran

ironpaw

Posted
Posted

wow that sounds like a cheap fix :) maybe ill give it a shot this weekend :))

LOL you gonna disconnect the battery for a week?

TBH I think the problem will resurface after a few more weeks, maybe once the car is driven daily the strain on the ATTESSA system will probably cause it to come back...

Sage222 Rising Star

Sage222

Posted
Posted

awesome thanks Scotty will hit them up if import factory dont come through. what did they sting you for a read? can they translate the codes for you? and one last thing if the light doesnt happen to be on will they still be able to get it?

[END SPAM QUESTIONS]

:)

scotty nm35 Grand Master

scotty nm35

Posted
Posted

They only checked it, and told me the codes, they were in english and self explanatory as I remember. Give them a call and ask, tell them Scott sent you down.

The tcu doesn't show the codes with a malfunction lamp, that is for the engine only I think.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Dose Pipe Sutututu
      Another little story of weird shit happening

      By Dose Pipe Sutututu · Posted

      Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • MBS206
      R34 gtt rb25det neo timing belt kit

      By MBS206 · Posted

      It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
    • GTSBoy
      Another little story of weird shit happening

      By GTSBoy · Posted

      Still haven't put the injectors and R35 AFM in so we can tune the bloody thing for the HG highflow it got mid last year! I think I can forecast the upgrade path to a bigger twin scroll, external gate, Haltech, flex setup, Samsonas, dis dat, etc will be .... a while away!
    • Dose Pipe Sutututu
      Another little story of weird shit happening

      By Dose Pipe Sutututu · Posted

      Should have taken that opportunity to slot in a twin scroll turbo setup. Maybe next time.
×
×
  • Create New...