Jump to content
SAU Community

Recommended Posts

2 by weld raing 15 by 8 rims with hoosier 28 by 10 slicks about 75 % left 500.00

2 by hoosier 28 by 9 slicks about 75 % left 250.00

set of rays 17 by 9 +19 rims with fedral 275-40-17 tyres vgc 1500.00

2 by mt 26 by 10 slicks 60% 200.00

4 by nitto 275-40-17 race tyres about 75% left 400.00

r34 gtr trust 93mm cat back exh with catless pipe 500.00

r34 gtr trust 93mm cat back exh with extra muffler 500.00

trust 60mm wastegate 400.00

custom turbo 4in intake with twin large k&n filters 500.00

greddy t88 38gk turbo 22 cm rear 1350.00

4inch dump pipe suit t88 r32,r33 r34 gtr 400.00

sard 1000cc inj cleaned &flowed 700.00

pare nismo rrr581 turbos 320hp rare 1500.00

mark 0418783262

Link to comment
https://www.sau.com.au/forums/topic/403354-garage-cleanup-sale/
Share on other sites

vielside 4wd pressure controller hand lever type .. same as reece mcgregors drag car uses .. 850.00

4 pot willwood front brake kit with rotors for drag suit 15 or 16 inch rims r32,33,34gtr 1000.00

std 32 rear calipers with ebc red pads 300.00

std r32 4 pot nissan 32gtr front calipers 300.00

big clean up....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If the RB29 box in the car is a push clutch, then yes, you will need to deal with the pull clutch on the turbo box. You either buy a pull clutch and don't use the old one, or you do the things needed to convert the turbo box's clutch arrangement over to push. Which is a bit of a f**karound. "Making" a custom tailshaft is the easy part. But you will need to source the front clip yoke - the bit that goes into the output of the gearbox. These are not as easy to find. They are out there, but they don't grow on trees the way that they used to.
    • Indicator bulbs are way too bright to use as a "corner marker" (we call them parking lights too). Sure. Go ahead and do it. But realise that you wil need to come up with all your own wiring to do it, as no-one will have a standard howto worked out for Skylines. It's just a matter of abandoning everything that Nissan have done and starting from scratch. You'd probably be better off retrofitting tailght/brakelight globe bases into the front indicator housings and using the taillight circuit for your corner marker and the brake light as the indicator. You'd need to work out how to kill the marker circuit while the indicator is flashing, otherwise it won't flash on-off, just bright-less bright.
    • Hi. A little bit of an update. It maybe(hope not) looks like i would need a new tranny(it would be "maybe" a cheaper or better option anyway) So i need some info. I know i need a different propshaft(i can make custom one) LSD is not a problem cuz the engine will be still(for now) N/A RB20. So if i buy RB25DET NEO tranny...is there something else i need? I read something about push/pull type but i do not know if i need to "change" something or i can just plug n play onto my engine a go? Thanks for the advice  
    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
×
×
  • Create New...