Jump to content
SAU Community

Recommended Posts

1) ive put a walboro 400lph pump into a mates r32 gtr, was piss easy

2) nismo is direct fit into hoses and airbox(same physical size as stock units) Z32 is larger size (80mm) will need to modify air box or use pods, pipes can be stretched to make these fit

1) I put the Walbro in my 32, was a simple process and basically a bolt in, you just have to run a wire from battery ( I went from the alternator ) to the plug in the top of the tank, the walbro needs more voltage to work it best

2) As SiR_RB said, which is why I suggested the Apex'i kit, they have one that adapts to the Z32s and is what I have on the 32 and made a massive difference over the HKS pods I took off ( they where modified to suit the 80mm Z32s )

The setup on my 34 was a really good street combo, PFC, 600cc injectors with nismo FPR and nismo pump, -7s ( though after seeing Seans 34 with -9s I say go the -9s ), full exhuast ( though since you have a 33 just do from the dumps back, 80mm cat and 3.5 inch back ) cam gears set for response ( I had poncams but not necessary ) I had stock AFMs with the stock airbox, if you where going to put a stock airbox then I would say Nismo AFMs but if your happy with pods then get the Apex'i kit and the 80mm AFMs, with that it made 310+rwkw on 19-20psi

-9's are slightly more expensive because they don't come with actuators, but you would probably want to put adjustable actuators on them anyway. -7's do come with non-adjustable actuators but they are 14.7psi (1 bar) actuators from memory.

So i take it i need these,

http://www.kudosmoto...dett-p-835.html

+ some adjustable actuators

Random thought; Will the stock gearbox/diff's be able to take the extra power?

Edited by Booki

The GCG adjustable actuators are so much cheaper than HKS adjustables: http://www.gcg.com.au/index.php?page=shop.product_details&flypage=flypage.tpl&product_id=556&category_id=39&option=com_virtuemart&Itemid=101

You can re-use the factory actuators but they will cause all types of problems around 18psi because of the weak springs.

Random thought; Will the stock gearbox/diff's be able to take the extra power?

Yes. Just have a little mechanical sympathy... IE DONT be a complete and utter moron with it and they will be fine.

Z32 and Nismo AFM's are not truly identical. There is ever so slight difference in the resolution/mapping of the AFM voltage.

Its minimal and hence for all intents and purposes they are "the same". Go Nismo however - cannot beat bolt in replacement.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...