Jump to content
SAU Community

Recommended Posts

hey guys i have up for sale the following two sets of wheels.

Wheel no1

Weds Kranze Lxz chrome finish.

18x9+22 f

18x10+31 r

wheels comes with tires around 70% tread. wheels are in good condition. no buckle or chunks missing from wheels. wheels do have your usual gutter rash.

8ed1d3b0.jpg

e20a65d5.jpg

Price $2600 ono. happy to send interstate at YOUR cost

wheel no2:

SSR professor ms1. these are EOI atm as im not 100% sure if i want to fit them to my car or not.

wheels are finished in hyperblack chrome.

specs:

19" x 9 offset +11 step lip

19" x 10 offset +11 step lip

wheels are in good condition. cpiple of minor chips here and there. one wheel has a slight rash. nothing deep. will see upon inspection.

dont have any pics of the actual wheel yet. will post up soon.

$3000 ono

thanks

Ash

  • 2 weeks later...

Hey ash have a mate from JDMST thats keen on the MS1's are these the ones pictured here?

Where u located for trial fit?

http://www.skylinesaustralia.com/forums/topic/403213-nsw-fs-full-set-of-ssr-professor-ms1-hyperblack-chrome/

for sale: full set of SSR Professor MS1

specs:

19" x 9jj offset +11 NR with step lip

19" x 10jj offset +11 SL with step lip

hyper black colour with polished dish

sbc_lrg.jpg

condition of wheels is great with minor chip and mark here and there but nothing major.

there is one rash about 25cm from previous owner on one front wheel but is superficial and can be machined out easily (can arrange for this also), can arrange tyres also if need be.

RRP for these wheels are $900 per wheel before special coat and shipping

pics below are of the actual wheels on the car they were on (not a promo pic)

img8901z.jpg

img8920s.jpg

20120623143652.jpg

selling the set cheap for $2300 shipped anywhere in australia

pickup available also

please pm me

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That’s a beautiful setup Tao, Have u done any development with the new Turbosmart 40mm electronic straight gate, especially in this G30 configuration?
    • Let's hope that's not a copy pump either. There were so many copies of them back in the day.
    • Damn it, I was at work last night, and stayed in a room there during the storm with the car outside, but undercover, I just went downstairs and well....there was a large steel locker that has come from some place last night, it wasn't anywhere I could see yesterday, and yeap, it landed on the fraking car....of course it did..... LOL So, I'll need to take it back for paint and panel, luckily it was only the boot that took the hit, so it could have been worse Serves me right for staying at work and getting on the cans with some of the boys
    • Yeah, really happy with how it all turned out As for aftermarket lip, nah, I'm not really a fan for practically reasons on a street car that gets driven everywhere  I did have the full lower kit on my 2015 STI, but found the front lip scrapped alot, even at stock 4x4ish ride height As the NC sits now, with the lowest point of the car at 110mm, so just legal, some steep driveways and steep speed humps will still "just" scrap those little plastic OEM air dam thingies on the undertray just before the front wheels
    • Here's one I help build and tuned a decade ago, Garrett  GTX3071R Gen 1, T3 twin scroll 0.83 rear housing. Went from larger 272 cams down to smaller Tomei Poncams to help with the low end. S13 non VCT motor. Car was purpose built for the track, hence low down was the focus. Note the actual dyno chart shows lower boost, however the EBC and boost gauge showed 1.9Bar (Ignore the torque, I was young and didn't know how to set derived torque)  
×
×
  • Create New...