Jump to content
SAU Community

Recommended Posts

Maybe email caltex and see if they plan to increase eflex availability in Canberra anytime soon?

Might flick them off something this afternoon.

Nicholls caltex, just off the barton highway

another southside somewhere.

it is not a practical solution in canberra yet as there's only 2 pumps

Okay so certainly on two pumps in Canberra?

E85 is only available at *non* woolworths Caltex outlets - Nicholls and one of the 2 in Kambah are the only non Woolworths branded ones in Canberra.

No plans for introduction at Woolworths Caltex outlets any time soon (an immediate family works in the Woolworths head office in Sydney).

Edit: and before anyone asks, Woolworths Caltex branded outlets are *not* Caltex, so ringing them wont help much - they are Woolworths Petrol with the fuel supplied by Caltex. Woolworths Petrol has no plans at the moment to introduce E85.

The "Star Mart" branded outlets are the Caltex owned/franchised shops and are the only ones that will stock E85 - aside from the 2 listed above, there are no other Caltex owned/franchises outlets in Canberra.

Edited by Amaru

wmi has no effect on your injector size, same size injectors you would run for what ever power it is on normal 98 as thats all you put in the tank.

good wmi kit 400-600, you then need to source your methanol and distilled/demineralised water, its not a complete retune its only a partial retune anywhere on the map after the WMI has turned on as thats the only place that will have any changes

for extra go fast you can mix in small amounts of nitromethane as well

You can get 20l drums of methanol for like $70 from a few places locally, which will last a fair while with street driving.

Distilled water is cheap as from any supermarket cleaning isle as well.

Kit will cost like 500-1000 depending on the setup you choose, but you should be able to put in yourself.

It's much of a muchness in cost difference I think, because setup/tuning costs are relatively similar and although eflex is cheaper, you can't go as far on a single tank. So that helps even the cost difference there as well.

You can always sell the kit and go e85 down the track if it becomes more widely available anyway...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • So was there a solution to this problem? I’m having this issue now. 
    • not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...