Jump to content
SAU Community

R34 Gtt Neo Engine Turbo Id Has Garett A/r .60 M24 N1 On Com Houseing And No Id Plate Has Ceremic Wheel Comp And Exhaust.

lcxu105

By lcxu105,
in Engines & Forced Induction

 Share

Recommended Posts

lcxu105 Proficient

lcxu105

Posted
Posted

ok i know there has been lots of people on here asking to id their turbo's and i'm new to this so bear with me.

On the com houseing it say

GARETT A/R .60 N 1

on a raised section inbetween the N and the 1 it says oy2a or could be OY24

there is no id plate on the turbo as this would make it easy.

i do know it is a ball bearing turbo as it has the 10mm nut/ bolt in the centre between the comp houseing and exhaust houseing.

On the back side of the exhaust houseing it has cast into it c op6

The waste gate has part number ASN82 33 in large painted numbers/stamp then under that has 1221A

I have also notised that on the back of the comp houseing is marked 1D416 maked on with a pen/paint

Any help would be great

Thanks Dave

lcxu105 Proficient

lcxu105

Posted
  • Author
Posted

that tells me alot.

I want to know if it is a t25 t28 gt30 or what the hell it is

If it is a n1 turbo.

what is the max boost it can cope with and how long they last for?

Jeremy93 Collaborator

Jeremy93

Posted
Posted

It's a standard r34 gtT turbo. It can run infinity boost. And the best thing is its legal! Yayayay

Now don't be a tart and accept that it's stock.

Inbeforetailor

wolverine Grand Master

wolverine

Posted
Posted

Stock neo turbo.

It will be good for about 200 - 210rwkw give or take 10kw.

Max boost is limited by your imagination but history shows that it will live a longer life if you stick to 10-12psi and won't make much more (or any more power) if you lean on it harder but you will end up with turbine in the cat disease sooner rather than later.

It is also in your interests to spend some time searching on SAU. Any question you can think of has been asked and answered many times before particularly when it comes to stock turbos.

GTScotT Grand Master

GTScotT

Posted
Posted

i thought the neo op6 was a hitachi like the other stock RB25 turbos?

since when does a neo run a garrett?

wolverine Grand Master

wolverine

Posted
Posted

I went all sorta silly and ran a search and guess what I found......

http://www.skylinesaustralia.com/forums/topic/69089-differences-between-r34-and-r33-turbo/page__view__findpost__p__1527454

The Dan Grand Master

The Dan

Posted
Posted

Yeah but what boost level?

i thought the neo op6 was a hitachi like the other stock RB25 turbos?

since when does a neo run a garrett?

All RB ball bearing turbos are Garrett

Watch-out-we-got-a-badass-over-here-meme.png

LOL

lcxu105 Proficient

lcxu105

Posted
  • Author
Posted

Ok from what you have all said it's just a std turbo, thats fine and will only handle max 12psi thats fine too, as i have the engine in a lc gtr torana. i took it to willowbank and shit the clutch and roll through for a 13.6 @101 so i know the car has a lot more in it as i stuffed the start and killed the clutch and was only running 8psi.

Current mods to engine are s1 pom cams std ecu 3" turbo back exhaust 100cel cat and free flow exhaust split fire coil packs and a 600x300x76 intercooler. soon to recive new clutch from extreme clutch part # kni25003-1r

From what i can make out the engine is out of a s3 as it had the red writing on the engine cover and the turbo has a metal twin blade comp wheel.

Dose anyone know who is the best to talk to about hi-flowing the turbo and fitting steel exhaust wheel.

wolverine Grand Master

wolverine

Posted
Posted

Cool, I had an LC Torana as a paddock basher when I was 16.

There is plenty of usable power to be gained in an aftermarket ecu...PowerFC, Vipec/Link, Haltech etc.

Aftermarket turbos has lots of threads here in Forced Induction with the most commonly spoken about being Hypergear but there are a huge number of options so name a target power figure and that will narrow it down. Click the search button and read.

GTScotT Grand Master

GTScotT

Posted
Posted

Lol very funny old timer, I missed that one when I looked myself. I did actually check first as I didnt want to make a dick of myself. Want not want whatever dick made, hooray lol.

thanks tho, its something I wanted to know :P

wolverine Grand Master

wolverine

Posted
Posted

Lol very funny old timer, I missed that one when I looked myself. I did actually check first as I didnt want to make a dick of myself. Want not want whatever dick made, hooray lol.

thanks tho, its something I wanted to know :P

lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 power steering

      By GTSBoy · Posted

      49719 is the cooler loop. Right at the front, LHS of that diagram. Return line from rack (LP side) goes to cooler loop on RHS front of car, then back under engine and returns to bottom of tank. 49717M is feed from tank to pump. HP line out of pump is thick rubber, followed by the hard line that runs down to crossmember and runs in parallel (but opposite flow direction) to the LP return line. Nothing goes anywhere near the firewall or interior of car. The closest they get to that is the connections on the rack.
    • drifter17a
      R34 power steering

      By drifter17a · Posted

      Thanks, plan is to drain all fluid tomorrow and do smoke test to find out the leak.   Appreciate your help and want to understand how the system work. So cooling is achieved by the long loop not any rad? The diagram seems to suggest it connects to somewhere inside the cabin and I thought that is a cooler inside firewall. If you look at the diagram it seems to show it connects to something inside firewall. I tried chasing it but not easy unless I take loads off   i am confident pump is good as fluid goes in and it gets soft( steering) but as soon as I turn engine off , loads of bubble come to surface and overflow. When engine is on , fluid level is below minimum but when off it shoots off and thinking it is sucking air in. I suspect aluminium pipe may have a crack line or whole   smoke test with no fluid should be a good start and if needed will remove the pump   In addition, the one going under the engine bay is high pressure line and one directly connecting from pump to resorvoir is return/ low pressure?   finally I searched and suggestion is to use dexron 2 but that is discontinued so bought dexron 3 as all research suggest it is compatible and shouldn’t cause any issues/ blow seals. I bought two liter of dexron 3 motul atf
    • GTSBoy
      RB25 S2 Idles but doesn't want to rev

      By GTSBoy · Posted

      Don't worry about. Just don't try to drive hard enough to make boost and you'll be fine.
    • GTSBoy
      R34 power steering

      By GTSBoy · Posted

      Yes. This has already been said. It is a loop of hardline in front of the radiator. Because.... the pump is on the LHS and the steering rack hydraulic connections are where they always are on a RHD steering rack....on the RHS. The high pressure line goes down under the engine, along the crossmember, like it does on all Skylines. Don't just throw expensive braided hoses/other kits at it. Work out what is wrong and fix that.
    • Trilbyte
      RB25 S2 Idles but doesn't want to rev

      By Trilbyte · Posted

      Still got the afm on the intake, clamps are shut tight, only loose hose is the one that goes from the j pipe towards the IACV, since it's next to impossible to find a factory hose and the barbs are different sizes (I'm still using clamps on this hose to try and help it seal on the iacv side) I've ordered parts to make up the hotside of the intercooler pipes, I'll plumb it in and see what happens in a few days I suppose The turbo's internally gated, can I just unscrew the tension rod to let the gate open?
×
×
  • Create New...