Jump to content
SAU Community

Recommended Posts

my r34 gtt had been sitting for a while and i just had new oil chucked in, plugs, and cranked her over (open dump ) and the turbo spat a fair bit of oil out the dump? could my turbo be gone? its got no shaft play, no stuffed fins, physicly looks great ? i dont really want a turbo upgrade as it was fine for my likings previously

anybody got a idea? theres also abit of oil in the front of the turbo aswell :(?

oil in front -blow by recirculation (normal)

oil out dump- slight wear on valve guides allowed a few drops in the chambers from sitting so long , got burnt on first start up.?

Edited by SliverS2

yeah well it was a lil wild i took pics of the fins etc, im not running any more boost then standard so I wouldn't of assumed its popped as the fins are perfect too, a whole oily smoke cloud and a cough up of oil came out the dump( first time start today since march or april . I haven't attempted to start it again after the oily incident

hard to say without the history of the car etc, sounds odd, at times like that with long periods of not starting i always disconnect fuel pump, and make sure i crank the engine for a while to make sure it has some oil in the top end before starting it.. starting to sound like a blown turbo seal, you shouldnt have actual oil coughing out i dont think.. :whistling:

Well you can start by checking engine oil level making sure it’s not over filled and the rubber on the hard oil drain pipe is not kinked or blocked. The turbocharger usually leak out oil from both ends if it can't drain oil fast enough or can't drain at all.

Once above has been checked with any issues repaired, start and idle the car for couple of mints see if the smoke clears away.

If not it would be likely been that this turbocharger needs a service, Do check out our turbocharger high flowing thread and alternative options available if that appears to be the case.

how much oil is in the sump, have you made sure the oil is actually returning in the sump or the sump isnt way over full like hypergear said?

i was of the opinion that the oil flowing thru the turbo and down that return was not a great amount, so to be flushing out the mouth kind of sounds like theres a blockage... id investigate more before turbo replacement...

the oil return line was replaced by me flange and all fitted and a new hose was fitted, had so much flow could compare to a radiator hose... (sarcasm) and the feed lie has no dints not damaged everything was fine...if i run the motor with the feed and return DCd i should see oil come through the feed line correct? ill double check it tomorow.. all i know is ill be chasing a r33 turbo if anyone has one there keen to get rid of?

another theory was that it could have been heaps of blow by that went through intake and out the top feed of the turbo? i put 4.2L of oil in my neo, dipstick reads perfect, :(

Im running a impul r34 computer.. im not sure what its capable of, but if i bolt another turbo onto it and run a few pounds more, will the computers air fuel ratio work it out so i wouldnt require a retune? or will i need a whole new computer all up?

Edited by nismokiller

well you have your breather tube that goes into your intake ? from your covers? Just a theory , but what if oil had come through there and out the top (intercooler pipe) I really wanna sus this out just so i have a good understanding of the problem im currently facing!

Id find it hard to believe that oil thats been sitting in your intercooler and piping could get sucked up enough to spit oil out exhaust at idle, I know what you mean though, and very possible theres oil in your intake, but cant see that much getting in? Have you tried starting it again?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I remembered wrong, but was close though 1Kz setting because those Jaycar SSRs don't go any faster, 1x pump per SSR with flyback diodes & heatsinks. In saying that, the heatsinks are overkill. Just on an alloy plate is more than sufficient. You'll find without a flyback diode, your SSRs will heat up big time and also die prematurely.  I've been running the two same SSRs since the last motor, no issues, car does 2 hour straight drives in summer once in a while and gets punished on the track. Nothing melts, no hot messes, etc.    
    • Hmm. You're probably best off working out what the lobe centreline or even the LSA is for the stock cams, with VCT OFF. That's bound to be out there somewhere. Then, work on the assumption that the Kelford centreline is probably the same, and wouldn't be more than a couple of degrees away, if it is different at all. I'm very surprised that you needed to adjust the exhaust cam by 5° to get it on spec. That screams there's another problem somewhere. Anything from the belt being 1 tooth off (how many degrees is one tooth worth?) to simple user/measurement error on the degree wheel. I say this because Kelford, like most quality cam manufacturers these days, does a pretty good job of actually making the cams to spec, not relying on patching it up afterwards like we had to do back in the 80s.
    • Besides packing it, you can also fill your pump through the oil filter inlet port. After cranking for what felt like an eternity without pressure, i fed a tube in through there and filled it with oil. Cranked for a few seconds after that and had pressure. 
    • That's exactly what I told myself. I'm happy it came out. 
    • My bet is there's a fuse somewhere you blew that feeds power to the ECU. Or you've bumped something out behind the dash board.
×
×
  • Create New...