Jump to content
SAU Community

Recommended Posts

G'day

Hi mates, i've got a Apex'i SAFC (Bule screen one) , just wonder what is the good setting for R34 GTT?

My aim is just a little performace, because it's for daily work use. (Fuel)

This is my setting now:

*Hi-Thrti * *Low-Thrti

1000rmp+2% 1000rmp-2%

2000rmp+2% - 10%

3000rpm+2% -0%

4000rpm+3% +2%

5000rpm+4% +3%

6000rmp+5% +4%

7000rpm+2% +1%

8000rpm+2% +1%

*Throttle

LO HI

25% 50%

*Dec.air

Thr....%

Nei: 1.0%

Ne2: 1.5%

Cheers

steven

Link to comment
https://www.sau.com.au/forums/topic/40432-your-opinion-on-apexi-safc-please/
Share on other sites

You will need to tune it on a dyno and richen/lean based on your A/F ratio. You cannot just add it in with "feeling". If you get it wrong, you will definitely destroy your engine. Every car is different, exhaust, air filter, boost level, all can cause differences and therefore your setting may not be able to be used for on other cars, also you can't just plug in the numbers that your mate has on his SAFC just because the other person has an R34 GTT too.

Decceleration Air is only needed if you have an atmo-venting BOV (aftermarket).

Mine still on 0%, untuned...... trying to book a time on dyno sometime next weekend and should have a result by then. It's a R33 GTS-t though, not R34 GT-T so I dunno how are you gonna compare it.

Cost varies from place to place, but a group dyno day (run only no tuning) will cost around $50-100, and tuning maybe somewhere $100-150 onwards depends on how much needs to be done. But I don't own a workshop so ring around for prices. I could be wrong.

I have an r33 GTST with an safc, your looking around $110 an hour on the dyno + wateva you organise with the workshop for tuning, usually on the dyno for around 1 or 2 hours give or take depending on the car. Get i professionally tuned dont stuff around with it yourself, if the car runs lean you'll get detonation and you dont want that!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So we have most the interior back in, and for the first time with one OEM speaker hooked up. The 31 is running, driving and now tunes!!! Hahaha yet another step for the sub that sat 10m under for two weeks!!! unbelievable really 👌 lots of love work and not giving up on her. Seen so many youngsters part way less, and in way better condition. I’m stubborn, thinking another problem is just a hurdle to overcome, One at a time. IMG_9277.mov
    • That is correct. I'm using a modified ABS ring and a ZF speed sensor on my rear diff for speed input. I'm running a Haltech ecu. 
    • Been busy with the newborn. We originally thought we were going to go for a third, but we're good with two lol. He's starting to actually sleep now so I've had some energy to work on the car. It's been parked away in the garage since late November due to winter.  I went ahead and redid all my head oil drains. I originally had my front and rear head drain going into the same pipe but have since split them up. I also added an Ethanol content sensor to get ready to run E85 this summer. Tossed it on my return line. Sensor sits nicely under my intake manifold.    I also have a lot of parts that came in for my rear end. I'll be swapping over to a 3.3 final drive and doing the GK teck anti squat mod. While the rear subframe is off, I'll also change every bushing. We're planning on buying another house soon with the condition that I get at a minimum a 2 door garage, so I'll wait to have more room for this. Now onto the strange things that recently happened... After changing the lower rad hose (It had been sitting in my cabinet for well over a year and was the last hose I had to replace), I let the car idle in the garage to bleed my coolant. After running for a few minutes, it started missing. Got much worst within a minute or two and then stalled and would not restart. My crank sensor decided to crap itself. No damage, no explanation, just died. I went ahead and replaced it with another ZF sensor but the heavier duty stainless model with a shield. Tossed that in and started right up. Has anyone else seen this? I hate when things fail without cause. Luckily this was a blessing in disguise... This lead me to recheck my timing. It seems I may have had a beer or two the last time I had set my TDC angle as I was off exactly 5 degrees... I miscounted a line haha. I was running 5 degrees less then commanded. It's a little embarrassing but helps explain why my dyno operator seemed to think I should be making more then 478rwkws.        
    • Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
×
×
  • Create New...