Jump to content
SAU Community

Recommended Posts

Hey guys I'm currently making 307rwkw with the following fuel setup ( custom fuel rail, 875cc injectors, adjustable fuel reg and a 044 pump ) an of corse the supporting mods to make that power. My question is I'll be doing some more work on it very soon and aim for 350rwkw is my current fuel setup enough for that power or should I be looking at doin a surge tank and another pump?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/404975-fuel-setup-for-350rwkw-r33-rb25/
Share on other sites

What car and fuel? On 98 it should be fine, on E85 those injectors might be a bit on the small side. You might also run into problems with your fuel lines, I've seen a few cars hit a wall in power at ~320rwkw with the standard fuel lines a restriction. Others have gone over 400. The pump will be pretty close to it's limit, but should still be ok.

360 kw on E85 here..... O44 is maxed on its safe limit, injectors and rail are ok (1000cc)...... Standard fuel line needed to be replaced in mine BUT pretty sure 33 won't need to be :)

I couldn't find his sig cause I'm on my phone:/ will check it out tonight on the puter.

Because I'm a nice guy ;) This is Matt's sig list:

Engine: Haltech PS2000, Wideband setup, ethanol content analyzer, GT3037-56T (.82 rear) with custom braided lines, Tial 44mm MV-R gate, custom dump pipe with heat wrapping, high flow cat and Apexi exhaust, HKS EVC 5 Boost Controller, 6Boost Manifold, Tomei 260 Type B Poncams, Exhaust cam gear, Gates Racing timing belt kit, Aftermarket Springs & Retainers, 4"intake with drift pod filter in custom JJ airbox, Plazmaman Pro series intercooler, Plazmaman piping, Plazmaman intake plenum and 66mm throttle body, Splitfire coil packs, GFB respons BOV plumbed back, Powdercoated covers by Craved Coatings, Black Works oil cap, Alloy Radiator air defelctor

Fuel: Bosch 044 fuel pump, XSPURT 1000cc injectors, HKS fuel rail powdercoated black by Craved Coatings, Billet fuel filter, SARD fpr, speedflow fittings.

Drivetrain: Exedy Cushioned Button clutch, Nismo 1.5 way diff, Nismo shifter.

Suspension: Tein SS coilovers, Front ISC adjustable caster rods, superpro camber kit, 27mm Selby swaybar. Rear ISC adjustable camber arms + Traction rods, Alloy locking rings & 24mm Selby swaybar.

Wheels & Brakes: 18" Works XT7's (F8.5 R9.5) powdercoated black, Kuhmo KU36 tyres, HEL braided lines, Endless front pads and rotors ,Endless pads rear.

Exterior: Carbon weather shields, Eyelinds & Bonnet lip.

Interior: Brown Davis Roll Cage, drift harnesses, Pioneer/Alpine/Fusion stereo.

Edited by Hanaldo
  • Like 1

Well Matt has always been a nicer guy than me! :P

Price for converting to E85 is pretty subjective mate, there's so many ways to do it. I've seen quotes from as low as $1500 all the way to $5000+. The way I believe to be the best and the way I would do it is also the way Matt has done it. Not cheap though.

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yes.  The only scenario I can imagine when the answer isn't yes, is if you drive like there is highway patrol behind you at all times.  If your car currently runs, enjoy it and keep saving. Better costs more, keep saving until you can budget the better ECU. It's worth it.  Nope. Plenty of us making >300kw on unopened motors. Mine is unopened and makes about 350kw if I turn everything up, its fine (lots of caveats here, how the car will be used/abused, how long you expect the engine to last between rebuilds, how has the engine been maintained prior to coming into your ownership, etc etc).   
    • Sorry just wanting to clarify, at this power goal, which should I be going? Also, More info regarding suspension, the rear upper camber arms were used to get the camber back to i believe around -0.5 ~ -1 degree (@ Road and Race in Rydalmere), I forgot the exact figure, but ALOT less camber than what it came originally which was like -2.5degrees. Are the traction arms still recommended? The bilsteins from SydneyKid, they've got 400lb/in fronts & 275/in in the rear, revalved to his specs. Intercooler, I'm just having a look at some on Rakuten.jp and some other japanese sites. Might get something from back there, GReddy, Blitz or HPI, all crossflow. Looking at roughly $450-$500 AUD + shipping... Theres not many choices except that chinese branded Justjap unless you go for blitz return flow. Yeah, only downside with Haltech is the price ahhaha, so expensive, and with all the sensors if I go that route... $$$$$ yeesh. Are headstuds/gaskets needed for <300akw?
    • Haltech fanboi reporting in. Buy the Haltech! 
    • You can try shoving a borescope down there to see what's up.
    • I could see someone trying this to save money on oil changes.
×
×
  • Create New...