Jump to content
SAU Community

Recommended Posts

Hi have a 95 r33 gtst clutch and driveline feels fine untill u give it a bit it has a loud wine over 5000 rpm in every gear and feels like the power isn't getting to the ground properly there is no diff clunks or slapping between gears it has smooth changes once car is warm the oil was changed in the box recently any answers?

Link to comment
https://www.sau.com.au/forums/topic/405334-gearbox-problem/
Share on other sites

NPC seem to be the popular option on SAU lately... I currently run an Excedy Cushioned Button and its OK but may not hold the new power for too long...

Make sure you get it diagnosed properly before spending any $$$, Where you located?

Link to comment
https://www.sau.com.au/forums/topic/405334-gearbox-problem/#findComment-6454736
Share on other sites

mate simple way to check if its the clutch, put it into second gear while sitting and try and take off, if you basically go no where then your clutch is stuffed, another way is while your driving just push the clutch in and out once quickly without taking your foot off the gas if the revs go up and takes ages to go down or just stays high your clutch is rooted

Link to comment
https://www.sau.com.au/forums/topic/405334-gearbox-problem/#findComment-6463800
Share on other sites

  • 1 month later...

hey just wondering if someone could help me out with a problem im having with my r33 gtst. when i start my car in the morning the car wont go into gear unless the car has been warmed up for at least 5-10 minutes and when it does go into gear the clutch grabs as soon as u lift the pedal but goes back to normal after driving for a while. any help would be much appreciated

Link to comment
https://www.sau.com.au/forums/topic/405334-gearbox-problem/#findComment-6551935
Share on other sites

hey just wondering if someone could help me out with a problem im having with my r33 gtst. when i start my car in the morning the car wont go into gear unless the car has been warmed up for at least 5-10 minutes and when it does go into gear the clutch grabs as soon as u lift the pedal but goes back to normal after driving for a while. any help would be much appreciated

You are either: out of clutch fluid, clutch needs adjustment at the pedal, slave needs bleeding OR you need a new clutch.

Start a new thread if you want an answer.

Link to comment
https://www.sau.com.au/forums/topic/405334-gearbox-problem/#findComment-6559510
Share on other sites

You are either: out of clutch fluid, clutch needs adjustment at the pedal, slave needs bleeding OR you need a new clutch.

Start a new thread if you want an answer.

thanks mate will try do somethin about it this weekend if i can figure it out

Link to comment
https://www.sau.com.au/forums/topic/405334-gearbox-problem/#findComment-6565780
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, I’ve just finished fitting the timing belt on my RB25, following the standard procedure: rotate the crank twice, release the tensioner, then tighten it down. The belt feels tight, and you can see that clearly in the picture below I’ve heard some people say it’s actually better for the belt to be slightly loose rather than too tight, as excessive tension can lead to snapping. So that’s in the back of my mind. What I’m seeing is this:  • At idle, the belt looks fine.  • But when cranking and especially when revving (around 3–4,000 RPM), there’s a momentary flap/flex or flicker in the belt, which I’ve tried to capture in the video. So my question is — based on what you see, is this slight belt movement something you’d consider normal, or am I just being OCD? Could this amount of movement cause sync issues? Or is it just a harmless bit of flex under load?   from what I know belt flap and flex is expected when crank spins up and pull cam with it Would appreciate any thoughts or similar experiences.     IMG_7656.mov IMG_7657.mov
    • I've replaced the front brakes of my NA to 324 brembos and 350z calipers: i'm going for 225/40-18 up front and 245/35-18 in the back. I have Rays 7.5*19 ET35(225/35) in the front with 5mm spacers otherwise the calipers "lock up/ won't rotate". When i use the calculator i come up with 8*18 ET30 for 225/40...... but not sure i get problems with the calipers. Anyone riding around with 18 inch. that can confirm "that it'll fit"? In the back it's 7.5*9 ET30 (245/30) with the 5mm spacers, but there is no problem with the standard small brakes, so i want to take 8.5*18 ET25 (245/35).
    • Lol.. but then.. always come back to a JDM..
    • Glad to hear. If possible, get your tuner to check air's to make sure everything is still where it should be.
    • The problem with FB/Insta/Reddit etc comments relating to cars is simple. You get to ask a question once, and get one round of replies. For things that can actually be answered in a few lines of text, once, it's fine. After 6 hours, your original question is lost to the void. There are no follow ups, additional questions, anything. No project car is ever such a simple list of questions to ask. You need discussion.
×
×
  • Create New...