Jump to content
SAU Community

Recommended Posts

Hey mate, why don't you just buy mine. Its an R32 with an RB25DET conversion! Anyway, the engine itself in good nick should only be around $2500-3000 with the loom n ecu. You will save yourself heaps if you do the installation urself with some mechanic mates as the labour is the real killer when it comes to overall cost. The previous owner of my car did this (He was 1st aussie owner of the car) which I had professionally inspected and everything was mechanically sound. Once all in, you will need an engineer's certificate to approve the mods cause you've increased the capacity of the engine, & any other mods, etc. Good luck - Hope this helps.

here's a rough breakdown of my costs for stuff from japan, i've got an RB20DE in my 32 GTS...

RB25DET engine - $1500 from a Series 1 R33 with wiring loom

Power FC + hand Controller + EBC usually goes for $1300 from supplier (i got a secondhand one for $900)

HKS Intercooler - $800

TD06 + manifold + wastegate + AFM - $1500

Shipping it all in a container roughly $400, haven't done it yet, will be leaving on the 20th

Putting it all together... hehe doin it all myself with a few mates.

Although if you're goin for stock gear it should be at least $3000 cheaper.

Mind you these are all AUD and also i pulled a few strings.

Putting in an R33 engine with a stock R33 ECU is a pain in the ass apparently because the sensor readings are all different on an R32.

I;ve got wiring diagrams for both cars so if you want em let me know.

hey yeah funky monkey would i be able to have the R32 and R33 wirring loom, as my mate has converted his car engine but he cant do the wirring loom so he has sent it away to be done and they can not do it either, so he is trying to track them down so he can do it.

He has converted a R32 gts to a R33 gts25 (yeah i know why not a gts25t, well thats because he is south african and we can not understand the shit he does sometimes)

yeah the gear box and dif out of a r32 gts25 will hold and also a gts-t gear box and diff will hold however the gts-t gear wont last as long as the gts25 gear box, then it all depends on how much boost you run and how you treat your baby. gts25 gear is around 2500 and a gts-t is around about 1300 dollars so the other alternative is to run a weaker clutch so if that gives you wont have to fork out as much money on the gear box......... the gear boxes in the gts 25 are the same as the gts25t andyway.....................

I don't plan on running high boost all the time, only when I'm on the track. Other times the car's used as a daily driver so I doubt the gearbox will get a thrashing.

The box will only give if I drive it like a d!ck and race everyone I see at a traffic light. I'm not into that shit anymore so I'm sure the gearbox will last a lil while, might have to change the clutch. I'll replace the parts as they give, coz the resale value of an R32 gearbox is pityful.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For sure the later RB26 variants had a different setup (6 cam voltage sender?), but the RB25DE/DET share the same ECU pinout/PCB footprint, and at the ECU plug it ends up being 'throttle sensor in' & 'throttle sensor out' (to A/T TCU) ...you stick a multimeter on these pins and you'll find them directly connected (0 ohms) ; I had an pair of Nissan ECUs on the bench long ago, and I noticed this throttle sensor in/out link, actually linked to an op-amp ...which was unpopulated on the NA board, but present on the T board and I went 'ah-ha!' in some moment of clarity... ...it wouldn't surprise me if they changed strategy here though (in the software and actual monitoring of this signal), because they did with other stuff (A/T signals).. and 0.45v as a trigger point makes sense, as that's what the external TCU units expect at idle ; kudos, thanks for that insight...I suppose it boils down to whether or not Consult can display real time data of that signal's voltage... ...in any event, it presents the same target...ie; rotate TPS unit to achieve 0.45v to suit both ECU&TCU, and where do you goto from there? Just disconnect TPSwitch connector and/or that plus TPSensor connector....or do you go for the throat and disconnect IACV solenoid and see if it still stalls? (probably throws a recoverable fault code and goes for default idle strategy?)...
    • I’m also conscious that e85 is slowly being phased out. Not all United’s have them anymore. Can’t take the risk of being low on petrol and assuming the servo will have it. 
    • MR HAMMER has said his piece. Painted up to avoid Rusty Rusty. Actually lines up well. (i.e it lines up the same as the unmolested GTR guard). Turns out the GTR Strut brace does foul on the bonnet vents ever so slightly. May need a little bendy bendy if intended to keep using with a strut brace. So spacing it out to clear the FAST102 is not an option. Annoyingly, the bonnet vents also foul on the heater lines running over the engine. Given this engine does not EVER require a heater, a delete loop is going to be used. Don't worry, the defogger uses the AC. The heater is basically "Do not use the aircon and turn the fan on". It will still be effective, I promise.... once I get the system regassed... Will have to revisit with unvented bonnet I suppose, and suitable strut brace. There's plans to do this and other things tonight and bleed brakes (there was a weep) and put the bumper back on, and take Good Friday morning - Because troubleshooting on the side of the road limping it home at midnight tonight is ... not very smart.
    • Thank you all for you assistance. I contacted Nistune regarding the support for the RB20DE along with my ECU Code (23710-10U00). They do have a map for it and added the RB20DE as a purchasable option now as well. They also added Malta as a Billing and Delivery options as this was missing. I was honestly amazed at their quick response and action, it took less than 24 hours. I also looked again at direct fit options for injectors, just in case I were to replace them. DeatschWerks seem to use a Bosch EV14 base and makes ones that fit mine at 440cc lowest, but also have 550cc at the same price. I tried looking for other direct fit options and managed to find one (also Bosch EV14 based) which includes a plug and play adapter on ebay. Did a small test with a Noid Light on the troubled injectors and all seems good, so they are pulsing properly electrically. One weird part is that they are missing on the same two cylinders as before I got the injectors cleaned. Mechanic also found this weird as he did not label the injectors and it is unlikely to have the faulty injectors be installed in the same cylinders.  
×
×
  • Create New...