Jump to content
SAU Community

Recommended Posts

Ok so my 32 has a little issue,

This happens In the morning or the evening after the car has sat for a decent amount of time, I don't run the car hard as it is a daily, 45 min drive to work.

Anyway, I get smoke out of the exhaust, it seems to be an oil smoke.

It comes out when I accellarate, but only once....I.e

Accellarate to 3000 rpm, will smoke ...do it again to 3 k...no smoke

Rev further to higher rpm and more smoke after 3krpm, make sense?

It seems to clear it out, like clearing your throat.

I always warm the car up never drive cold.

My thoughts were theirs oil draining/ seeping somewhere it shouldn't and being sucked back into the engine when I go again later on.

One it's cleared theirs no more smoke

What should I be checking here?

I do know from a service report that my turbo oil drain line had a slight weep, any link here do you think?

Edited by GH05T
Link to comment
https://www.sau.com.au/forums/topic/406304-smoke-in-the-morning/
Share on other sites

Possibly valve stem seals. Car sits and a small amount of oil weeps past the seal. Start car, give it a squirt and the oil burns off.

Give it a comp test and if it comes up chipper, then it's likely the valve stem seals as they won't generally, affect your compression. If comp is down then you have a bigger problem.

Then I'd say almost defo valve stem seals.

If it is valve stem seals I wouldn't be too concerned. Just make sure you keep an eye on your oil level and if it gets worse, like blowing smoke under power and or a lot of of smoke on start up, then it's time to look at getting your head refreshed.

That puff of smoke on cold takeoff is usually condensate oil from the PCV running down into the manifold overnight. You can try fitting a small sealed catch can full of stainless steel wool in the pcv hose to prove it.

That's what it seems like, from a stand still any acceleration gives a noticeable amount of blue smoke (visage at night in headlights behind) and like I said its like it puffs as far as it revs, but only once, accel to 2000rp with smoke but only once, more smoke when you go past that rpm again,

Is this problem going to get worse if the car gets driven hard? I drive daily and maby one in a while it gets a caining, should I be carefull, is their anything I can spenda bit of coin n to help further expenses ?

I always warm the car up never drive cold.

Drive it cold (but sensibly!). Most of the damage is done when the engine is cold. It will warm up much quicker than simply letting it idle.

And you won't be coming back later asking why your fuel economy is so crap.

dont care at all about fuel i dont pay for it, i run my car for 15 mins in the morning before driving, i run it for about 3-5 in the evening after work, nether affect the smoke though, its always the same

Blind_elk is right. Warming up vehicles, especially ones that rev, is a very bad idea. Generally at idle the oil pump isn't pushing a great deal of oil around and there's not much temp increase which means it takes longer to get oil everywhere and also up to temp.

Start car, let idle for 30 seconds then get driving.

Idling a cold car for 15 minutes is a great way to destroy rings and valve stem seals.

Yeah idling for 15 minutes is not a good idea at all, would barely warm it up, would get up to temp in 1-2 minutes of normal driving otherwise. Start it, wait 30 seconds then drive off staying off boost until temp is up.

Smoke could be turbo seal or valve stem seals.

Edited by Rolls

Valve stem seals means head off. In reality leaky valve stem seals won't do any damage (at least in your case as it seems not too bad.. They'll just progressively get worse until such time as it smokes a lot more or all the time and then it needs to be fixed.

I'm not sure how hard it is to get the head off an RB as I've not done one, but once off, barring any weird RB specific oddity, the seals might be maybe $100 or so and the work to actually fit them might be 4 hours (that's a pretty rough guesstimate). Of course, if it were me, with the head off and the valve train off it would be hard to resist giving the head a through going over.

As for turbo seals, that's a tougher one. That means turbo off and either a "back to stock" rebuild for $500+ or replace with something tastier for $1000+ plus required supporting mods.

TBH it sounds to me more like valve stem seals rather than turbo. I think if it was the turbo it would produce more smoke under load.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
    • Still haven't put the injectors and R35 AFM in so we can tune the bloody thing for the HG highflow it got mid last year! I think I can forecast the upgrade path to a bigger twin scroll, external gate, Haltech, flex setup, Samsonas, dis dat, etc will be .... a while away!
    • Should have taken that opportunity to slot in a twin scroll turbo setup. Maybe next time.
×
×
  • Create New...