Jump to content
SAU Community

Hicas Eliminator Kit

SCR48
 Share

Recommended Posts

boostn0199 Grand Master

boostn0199

Posted
Posted

Bear in mind it is a bit of a mission to do this at home as you will almost certainly need to take off the hub assembly to press out the existing ball joint bush.

You dont need to take off the hub to press bearings out, simple tool can do it on the car, even if you do need to take hub off its easy to get off no mission lol.

R.3.2.G.T.R Grand Master

R.3.2.G.T.R

Posted
Posted (edited)

i have one these kits sitting at home waiting to be installed.. i wanna do this at home but my concern is finishing the job over the weekend as i have read its a pain to press out the balljoints

boostn0199: what did u use for the job? how long does it typically take?

ps - i have a small dremel which i was thinking of using to cut of the lip on the balljoint and press it out from that direction - anyone done it this way?

Edited by BWRGTR
RB 30 Enthusiast

RB 30

Posted
Posted (edited)

Modification of a steering system. Not permissable without engineering.

Hope mine is hard to see under the rear diffuser... Pretty sure they will have a field day with the Decat pipe. Is my fuel system illegal 2?

Under Car, New Exhaust and Fuel System

Edited by RB 30
GTSBoy Grand Master

GTSBoy

Posted
Posted

Take my tip. If it is still in whatever garish colour it came in, take it off and paint it black before crossing your fingers. Will make it much less likely to get spotted. Cops may or may not be bright enough to know whether the car was supposed to have HICAS, but they can sure as f**k tell that a bright orange/blue/red component is not original.

RB 30 Enthusiast

RB 30

Posted
Posted

Take my tip. If it is still in whatever garish colour it came in, take it off and paint it black before crossing your fingers. Will make it much less likely to get spotted. Cops may or may not be bright enough to know whether the car was supposed to have HICAS, but they can sure as f**k tell that a bright orange/blue/red component is not original.

True that! I still have a airbox! and a cat some times lol

boostn0199 Grand Master

boostn0199

Posted
Posted

i have one these kits sitting at home waiting to be installed.. i wanna do this at home but my concern is finishing the job over the weekend as i have read its a pain to press out the balljoints

boostn0199: what did u use for the job? how long does it typically take?

ps - i have a small dremel which i was thinking of using to cut of the lip on the balljoint and press it out from that direction - anyone done it this way?

Basically i made up a mini ball joint puller and pusher so it pushes witha bolt to get it out. For me even if i did it with removings hubs wouldnt take memore than couple of hours.

  • 3 months later...
  • 1 month later...
AshR34GTT Enthusiast

AshR34GTT

Posted
Posted (edited)

Do ppl who put these lock out kits in, only do it to improve track performance, or do ppl experience issues with the HICAS on everyday road use?

I've never tracked my car, but I do know that when I engage HICAS on the road, I can take corners up to 20 km/h faster then when it is disengaged.

So just curious as to why do many ppl install lock out kits? I personally think HICAS is excellent, but like I said, never tracked my 34.

Edited by AshR34GTT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      Tyres you use(d) and how u would rate them

      By The Bogan · Posted

      Done about 5k Km on the PS5's now, excellent street tyres, great in the dry, and the wet, seem to be wearing very well, I haven't measured tread depth, but it looks like minimal wear, I also had a different alignment done about 1500km ago,  From looking at the tread wear, which is really only minimal, the alignment changes were based off how the tread looked, and how it felt throwing it around, the changes have shown great results 215/45 17 at 32 psi Front Caster: 5.5° Camber: -1.5° Toe: 0.0mm Rear Camber: -1.0° Total Toe-in: 1.5mm I actually prefer PS5's now over the RS4's, as the PS5's are much better in the wet IMO, and as the MX5 gets driven in all weather conditions doing daily duties, hwy trips, and blasts in the mountains, wet weather grip is high on my priority list
    • Russell2208
      Attesa ETS Pro Install on R33 GTR

      By Russell2208 · Posted

      To update this thread. I got sent a replacement Attesa pro unit and all is now working as expected. Cheers
    • Ozdavroz
      The FD RX7 is the best looking 90's JDM car

      By Ozdavroz · Posted

      FD is so sexy she can pull off tri-spokes
    • Butters
      Front LSD Quaife , how streetable ?- QDF3L Owners

      By Butters · Posted

      Indeed they do. Best my diff builder could tell is it's a combination of the different cut/angle and it would seem they lap them in well on accell but less so on decel. He had to use a slightly different pattern to the lap to get the best result noise wise. Also as the rear diff runs in, the whine is getting less.        Overall they seem like a good thing so far. He's done a few neat crown/pinion before but all for race cars with loud everything, in most cases the exhaust is louder, so I am the first to notice.... and be somewhat of a pain   
    • GTSBoy
      R34 4 door indicator and horn issue

      By GTSBoy · Posted

      What do you mean by "test"? It sounds like you're just switching things on and off that you already know don't work. Get the wiring diagram and a multimeter and start looking for power where there is supposed to be power and earth where there is supposed to be earth. Look for continuity across switches that are otherwise unresponsive, etc etc.
×
×
  • Create New...