Jump to content
SAU Community

Recommended Posts

I had a car cover on my custom painted rx7 outside all the time in LA cali and denver for 11 years , it wasnt a custom cover but flannel soft on one side slightly water proof but breathable on the other 1 layer of fabric , had some elestic around the bottom corners and lock with cable on middle of it , as you know acid rain is in both towns , snow a foot deep or more , salted roads in winter , criminals , windy as hell around 200kph sometimes in denver front range , sand , salty air in LA lived on a large boat ,batteship so car was parked on the marina all the time , truck soot the docks in fast and furious is where it was parked

Car cover issues

Wind will wind it up only the cable lock will keep it on and not in outerspace took about 60-70km winds to fling it loose

Snow when it melts it left the acid dirt sitting on the paint like a big filter of crap not likely here

Rain , it must breath or it will rot the paint and the cover , it has to be able to dry itself pretty quickly not sit soaking for days unless its still raining

Also leaves crap but not as bad

Car must be spotless on rub points if its tight

Has to be able to clear hot tailpipes

Mirrors must fit

Must be locked on always , it will fly off or be stolen

Overall it saved my paint job once it tore that was it the paint was stuffed from uv acid etc

Cant put on fresh paint either

bonus of cover

Theft deterent the crips tried to steal my car a thousand times but the cable lock setoff. The alarm easy it can be tied into alarm trigger they never got it !! stops people stealing tunes , out o sight out of mind

Car stays cleaner cause your careful more ,

Car is much cooler

Saved my car from hail a few times when other cars had windows knocked out and dings galore

Saves on dings and nicks a lot

Saves the bird poo

Mark it with your rego or the ticket police will love you , rego must be visible

Drawbacks

Cost up front 300+ for non custom one

Takes about 4-5 min to install if its not windy and put away properly thats a average you can do it faster if needed

If you dont like making beds forget it its very close to that haha

A soggy cover stinks in the boot / bag

Must be scotchgaurded often it looses it fast in the extremes

Can attract crims - curious buggers

Can attract graffiti artists

Must be used often and can be a pain to be so padantic about a car ( ladys hate to come second haha)

can scratch if your not careful

Catch fire on tailpipes

Yet another bulky item to take to laundry mat to wash ! Its heavy as fark wet home laundry will die

can mold and cause car inside to mold if your not careful in drying it

Now days microfiber ones would be great but hard to find unless you shop usa and they never had skylines so a custom one will be hard to find

Dont buy a plastic based waterproof one they kill the paint they dont breathe enough , only good if your not moving the car for months outside

in australia i think it would attract idiots ( vandals)

So i opted to not cover my car , maybe in the garage but out in the open i think it would be a week tops before it was molested Like a naked virgin by some wankers

Edited by Carbon 34
Link to comment
https://www.sau.com.au/forums/topic/407128-gtr-car-cover/#findComment-6495672
Share on other sites

  • 3 weeks later...

I had a car cover made by chief car covers in perth. I gave them my car details and thinks like height of wing. The indoor cover i got is awesome really soft and i am really fastidious with my paintwork (also if good quality car covers are good enough for show cars then good enough for mine). but still strong enough it will last for many,many years. At least give them a call or email and talk to them.

Link to comment
https://www.sau.com.au/forums/topic/407128-gtr-car-cover/#findComment-6524525
Share on other sites

there is no car cover that won't scratch. period.

see how imperfect the paint is on show cars next time and tell me covers are great... the covers are there more for branding/"the reveal"/exclusivity than anything else.

i suppose next we should all use paraffin dusters because that's what they use on show cars...

having a car cover for indoors is a waste of time. Outside... maybe, if it's a really harsh environment - But you're still better off having a good few layers of a very durable sealant on a car IMO, and then use a sun-shade reflective thing to give the interior a bit of protection.

Link to comment
https://www.sau.com.au/forums/topic/407128-gtr-car-cover/#findComment-6529720
Share on other sites

  • 4 weeks later...

I find car covers are good for cars being kept outdoors as it minimises the wear and heat hitting the paint, plastics and rubber lining in the sun - particularly if you drive the car say once a week on the weekends

i had a dodge supercheap auto special for about a week before i decided it was both rubbish and abrasive on soft paint - i ended up going with a Kenco Tyvek car cover, the inner lining is developed with paint manufacturer DuPont meaning it will minimize damage to your clear coat

the best thing about it however is that even thought it is weatherproof and UV resistant, it is the lightest car cover i have come across meaning you can put on and take off the thing by yourself without letting it touch the ground - also comes with repair patches incase you manage to rip or tear a hole in it

Fit-wise i went with the large size which covered my R34 with the big trolley wing perfectly

can be had for around $100 when there are sales

http://www.superchea...258#Description

pic of it on my car;

cover_zps169f0808.jpg

cover%20close_zps0a49cb8a.jpg

Edited by squareznboxez
Link to comment
https://www.sau.com.au/forums/topic/407128-gtr-car-cover/#findComment-6565201
Share on other sites

  • 3 weeks later...

the flannel king size sheet sounds good. mines inside the garage but gets dusty as hell after 2 days

might buy a few wheels and screw it on the roof and string and have like a window blind type cover lol

Link to comment
https://www.sau.com.au/forums/topic/407128-gtr-car-cover/#findComment-6589697
Share on other sites

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • They care about emissions, and cost the most. Save weight where possible, and make manufacturing easier. Less material also let's the engine transfer heat to water quicker, and bring the engine up to temp quicker, better for emissions and getting them past their warranty period.
    • I was under the impression the reason why OEMs are going with solutions like relatively thin "right-sized" cylinder walls with technologies like PTWA and open deck is because they care a lot about whatever marginal knock margin benefits they get from that vs the structural rigidity benefits of a closed deck block and thicker cylinder walls. I also see some weird stuff like plastic inserts in the water jacket around the cylinders to try and equalize cylinder wall temperatures. re: the PRP blocks and heads at the end of the day it's hard to know what is and isn't going to work there, just have to see what the initial buyers say about it.
    • Which is why I didn't mention that hardness testing, and specifically mentioned the bore and deck thickness testing. Yeah, not really. The bore temperature will be a lot more even around the top half inch or so, where the material distribution is dominated by the deck, and which is the only place where the bore surface temperature heating any gas in the cylinder is likely to have any effect on detonation. Think about it. Another inch or so down the bore, you might have a hotter spot. The gas there might get a bit hotter, then the piston rises squeezes that gas away from there at high speed and mixes it with other gas from nearby. Instant dilution of the problem. I'd be surprised if it was an issue at any time other than in racing engines or OEM dev engines being run at the ragged edge of tuning. Say what now?
    • https://dsportmag.com/the-tech/education/engine-tech-material-hardness-testing/ The PRP testing on block hardness I'm not sure how much it actually can be trusted. The thinner cylinder walls on RBs is a bit of a problem vs 2JZ but it really depends on the design goal. Siamesed cylinder bores like a 2JZ cause uneven cylinder wall temps too, which means a bit of distortion induced by that + the hotspot can affect knock margin. Something that actually gives me a bit of pause with the PRP block, whether super thick cylinder walls are going to keep it from being drop-in compatible on an otherwise OEM rebuild. 
    • Yeah very valid point. I am waiting for one of the other tuners to come back from vacation so he can help me a bit when the cat is installed again. In the meantime I am going to finish up my polishing and ceramic coating that I have started myself.    N45 Dr Beasley product is highly recommended for a paint primer / polisher. Using this EXO Gtechniq also for the ceramic but next time might use the light serum before hand also. Looks great. 
×
×
  • Create New...