Jump to content
SAU Community

Recommended Posts

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

220-240kw R33 gtr, daily driver.

On the same car with 266kw of power I found the standard 595's too hard and slippery in the wet. The 595 RS-R's were actually far grippier in dry or wet even when cold and lasted for a good length of time.

595 if you have no money, 595 RS-R for safer driving (they are not real semi slicks).

But hey upgrading from the base 595's to the RS-R's shows you a huge difference.

Pirelli p7s are abit soft in the sidewall for my liking. Falkens have good grip, performance and cost effective.

Fk452 = best wet tyre ever, abit noisey like 595, directional, new fk453 out now to replace it.

Ze912 = good allround asymmetric tyre

Or for more coin go the Bridgestone potenza range re001, re002, s001. Very rigid tyre an very quiet.

I believe I'm running RE-001 and they're quite decent in both wet and dry. Can't really comment on their ability to hold traction under power in the dry any more since I think they dried out a bit too much in the months my car didn't move and was outside :(

I had the same RE001s before Troy bought them and I always liked them - they did me well for around 350-400kw atw and I did some pretty hard launching on them too.

Only sold cause I needed bigger wheels to clear my brakes. I went OTT and got semi slicks... Super impractical but f**king fun!

Or go to ntw talk to mick and then take your car/wheels round the corner to jax fyshwick where mick takes his cars ;) haha

Also I got 235/40R18 stretched onto my 9.5"s (widest legally permissible for a 235/40), tyres cheap as and it's the look I'm after.

do you have a picture of the stretched tyre?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...