Jump to content
SAU Community

Recommended Posts

So my wife's R33 A/C has been acting kinda funny lately. Even with the climate control turned completely off, the A/C still stays on. It blows very cold and all of the mode/blend doors are working properly, but it just won't stay off. Any ideas?

Link to comment
https://www.sau.com.au/forums/topic/407372-r33-gtst-ac-acting-wierd/
Share on other sites

Very good question! She says that she notices that the compressor cycles on and off even when the climate control is turned off completely. She does notice that when she has recirc on and the Climate control off she doesnt feel cold air blowing through the floor vents. But if she has everything off and its on fresh air even on a hot day she still feels cold air on her feet. I have rode with her and experienced this as well. I just cant figure out why the compressor is getting power with the climate control turned off completely. Possibly a stuck/shorted relay?

Edited by Gojira5767

Hi Gojira,The ac system has a self diagnose system,do a google search you might only find it for the R32,but it's similiar in function. hope this help's.Here u go found it for u http://www.gtr-owner...ic-ac-test.html.

Edited by I gotta R34gtr v-spec

Maybe you're hearing the AC fan kick in, not the compressor? the AC fan will kick in automatically when the coolant temp goes over 95C. Naturally you won't even realise coolant temp is 100C as the coolant temp gauge doesn't really go near the red till about 120C

Ok, so I ran the diagnostic and came back with code 25(Sunload sensor). Does this cause the A/C to come on automatically when its faulty even when HVAC is turned completely off? Mode doors are all operational, and Diag Mode 4 shows "41"? Im assuming thats a blower motor check, as it turns it on during this mode. And on mode 5, the temp sensors are reading 31 & 32. Which I calibrated both to 31 degrees. I guess I need to replace the sunload sensor regardless huh?

Also, I haven't noticed the A/C fan kicking on, but then again the temp hasn't gotten that high. I have Power FC's on both cars, so I am constantly monitoring it. But your right, the gauge doesn't accurately reflect how hot its actually getting.

Edited by Gojira5767

If u did the test in the garage or at night u will get that result,u need to do it in the sun light.If u want to try the r34 service manual,here's the link http://www.importworkshop.com/files/manuals/nissan/R34_service_man.pdf and go to the a/c section.

That makes sense. I will try it again tomorrow then. And I think I have the R34 FSM printed off somewhere. If I cant find it I will definitely use the link. Thanks! This is just such an odd problem, something has to be sending power to the compressor at all times. I may just replace the relay for kicks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, hydraulic lifters will get noisy if they are dirty/fouled in some way, and exactly how that manifests will depend on exactly what schmutz is where. There is a procedure on here somewhere for dismantling and soaking/cleaning them. Replacing them with new is about 50% of the work and about 5% of the money!
    • Thanks for the reply @GTSBoy this is is a hydraulic lifter engine. Yea right i did not realise the lifters were supposed to be compressible while installed. I could push them down but i had to lean almost my while body weight on them.  I have never heard of a lifter/ lifters ticking only at hot idle and getting worse the hotter it gets. I have owned a few jdm cars with noisy lifters. This noise is slightly more subtle, it is more of a sharp gentle metalic tic than the solid and more loud tapping I've heard on lifters. I have used a metal rod, alloy tube, hose and stethoscope and could not find the source of the tick. But it appears to be loudest on the actual engine block behind the exhaust cam gear and next to the oil filter. I had mate (40 year old mechanic) go over it with me and he couldn't find it either..  Could it be a cam seal issue of some sort?  Cheers  
    • This seems problematic and unlikely at the same time. Vanilla RB2Xs have hydraulic lifters. They do have "zero" clearance, but only when running with oil pressure inside them. When not running, you should be able to compress them and obtain heaps of clearance. RB26s and Neos have solid lifters. They should have ~0.3mm and ~0.5mm on the inlet and exhaust respectively. If they have zero clearance then bad things are happening. With nothing else being wrong, it would mean that the valves would be held slightly (ever so slightly) open when they are supposed to be closed and it should have all sorts of problems when running, caused by leakage in/out through the valves. Or, zero clearance can indicate severe valve seat recession. None of it is good. Have you used a piece of hose as a stethoscope to try to localise the noise?  
    • Sorry for reviving an old post, but I'm having the same hot idle tick issue. Did anyone ever find out what it was?  I have checked/ replaced Injectors Coils checked Lifter clerance (is at zero) Checked Cam lobes Replaced exhaust gasket and studs Would appreciate any advice this is driving me nuts  
    • There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
×
×
  • Create New...