Jump to content
SAU Community

Shout Out To Scotty Nm35 - I Have Boost Again!

ドッミ

By ドッミ,
in Four Door Family & Wagoneers

 Share

Recommended Posts

ドッミ Newbie

ドッミ

Posted
Posted

A big shout out to Scotty NM35 for all his help and skinned knuckles with the removal and install of my turbo!

New shorter core produced quite a few install issues and problems for Scott along the way. But he endured and I have boost again!

Coupled with a 'Scott Dump Pipe' and actuator mod, there is a definite extra kick.

Thanks so much Scott. Love your work.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

No problem Dominic, glad to help. Did you get underneath and check it out?

Not very happy with the way this turbo was installed, too many mods required to make it a feasible option. That said the stock like response felt good for an untuned engine.

You are lucky I waived the bandaid tax, costs could have blown right out. :)

Sunkist Grand Master

Sunkist

Posted
Posted

Welcome Dominic

Yeah, I hear Scotty does OK work :)

What turbo did you get?

Cheers, Leon.

Lol ok? There were SOOO many problems Scott had to fix after getting the turbo back.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Someone left the door open again, daym wastlanders...

It was the "stock" sized wheels that Stao just designed, only hassle was the chra was 21mm shorter meaning the compressor housing and everything hanging off it was 21mm further back.

I won't be fitting another one of these.

iamhe77 Grand Master

iamhe77

Posted
Posted

Someone left the door open again, daym wastlanders...

It was the "stock" sized wheels that Stao just designed, only hassle was the chra was 21mm shorter meaning the compressor housing and everything hanging off it was 21mm further back.

I won't be fitting another one of these.

Sounds like the same issue that Craig had when his 3071 highflow went on.

Sunkist Grand Master

Sunkist

Posted
Posted

Someone left the door open again, daym wastlanders...

It was the "stock" sized wheels that Stao just designed, only hassle was the chra was 21mm shorter meaning the compressor housing and everything hanging off it was 21mm further back.

I won't be fitting another one of these.

Pick up yo phonnnneee nigggahh

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Sounds like the same issue that Craig had when his 3071 highflow went on.

Exactly, even though I was promised it would fit as he had already sold two of them. It's easy to fit when someone else is doing the work though.

ドッミ Newbie

ドッミ

Posted
  • Author
Posted

No problem Dominic, glad to help. Did you get underneath and check it out?

Not very happy with the way this turbo was installed, too many mods required to make it a feasible option. That said the stock like response felt good for an untuned engine.

You are lucky I waived the bandaid tax, costs could have blown right out. :)

Haven't had a chance to climb under and look as yet... Got home from work in the dark yesterday, then back here this morning in the dark! Things one has to do to pay for repairs to a shagged M35 turbo!

Really impressed by the acceleration. As you said, close to stock. Very linear and coming on from approx 2500rpm with the extra kick.

My original post certainly didn't describe just how much stuffing about you had to do. Word of warning for anyone else going down this path... Speak to Scott and he will say, DON'T, I am sure.

Thanks for waiving the bandaid tax - with the number of cuts suffered, the cost would easily been higher than the value of the car!!

That was a mighty big look of relief in the rear view mirror, when I drove off - clearly happy to see my car disappear!

Sunkist Grand Master

Sunkist

Posted
Posted

That was a mighty big look of relief in the rear view mirror, when I drove off - clearly happy to see my car disappear!

relief?

hahah he was probably pissed off that he had to start mine

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Anyone have this problem with their temperature gauge?

      By sunsetR33 · Posted

      Read the ECU for fault codes or have someone else do it. A faulty coolant temperature sender is usually listed in ECUs. If the sensor itself is not busted it can also be a bad ground connection. Or in a really unlucky case, damaged wiring.
    • sunsetR33
      Anyone know this frontpipe?

      By sunsetR33 · Posted

      Can't be a Futjitsubo as those are made with a flex piece and Reimax is smaller in pipe diameter. If anything it is closest to a Mines pipe, but evidently it is not an actual Mines pipe.   Classic word humor
    • sunsetR33
      Anyone know this frontpipe?

      By sunsetR33 · Posted

      Alright I will try to not forget.   As GTSboy replied to you already, problem is mainly the mismatch between the actual exhaust part and the denomination in the papers. That basically just looks like tampering to a cop, if they were to check your car and notice. If it had been done right they would have clarified it to be a custom pipe and just given it a certain part number that you have to engrave or weld onto the pipe. I will definitely inquire on what to do. Changing the pipe wouldn't be my favorite solution as it costs a bunch of money and the cat was fitted with the front pipe and exhaust under the car, and if the front pipe flange does not sit in the OEM location the cat will need to be refit for any other pipe to work. It also usually doesn't need a brand name or something like that, but more something like a part number. Usually for exhaust parts, on silencers and cat units specifically, there is a badge that reads the certificate number that belongs to these exhaust parts under EU regulation. You get these numbers after you put a part or group of parts through the tedious testing according to EU vehicle legislation and they pass. You can find these "part numbers" on various parts throughout a EU vehicle. On windows, headlights, engine parts, seat belts and so on. All these parts have gone through standardized testing and acquired a so called ECE or EG Certificate that makes them legal to use by themselves in all countries that adhere to these standards. You can also not alter these parts in any way, if you do they become illegal. An example for stampings on an exterior lighting part, the people who need to know can find the documentation for this unit in a database. I do not know what all the standards and so on mean.
    • Rezz
      Anyone know this frontpipe?

      By Rezz · Posted

      If that was the case I suppose you could call it "Mein's" brand....  ... I'll see myself out... 😅
    • GTSBoy
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By GTSBoy · Posted

      Yes.
×
×
  • Create New...