Jump to content
SAU Community

Recommended Posts

I started this thread because there was so much stuff being posted that I didnt agree with in other threads, but I realize that not everyone wants to be strong

This thread is for those that do

So my posts in my powerlifting thread will always be about increasing your 1RM

Looks like I'm going to be getting lots of bench practice for the next week or two

did something to my lower back... right down the bottom, near my upper glutes... can't bend over at all... sitting and standing are very painful... lying down is okay... getting dressed is a challenge... might just go to bed clothed, will make things easier tomorrow lol

I've strained my erectors before but this is different... lower down and much more painful

I'm lifting at Nats... even if I have to do so in a wheelchair... so my back can kiss my arse

there's two vaginas... a front one and a back one;)

yep will be seeing Jason Mawby as soon as i get the correct phone number lol

leg movements are okay... walking not too bad... hurts to twist

anything remotely like a deadlift movement hurts the worst... TBH I'm pretty sure I did it last week... thought it was just tightness/soreness so I did a long warm up and lots of rolling... felt sore but I went for my working set anyway... it didn't pop or anything just knew as soon as I'd finished the set I was in trouble

just hit it with the hot water bottle and it's a bit better... which leads me to think it's just a strain... hopefully I can just skip squats/deads this week and it comes good

Wayne slipped on a roof and cut his leg very badly... Liam has a knee issue that he had surgery for... surgery didn't work but then they found another issue that needs time to heal

I think I hurt my back as a direct result of giving Wayne crap about having to load his plates for him... karma is a bitch

I'm off to see Jason tomorrow morning, then drop in at PTC for a bench session after... hopefully it's just an alignment issue, maybe a pinched nerve that can be fixed with some manipulation

That time of the year again. A few of my guys are riding that fine red line atm as they prep the final stages for nats.

Seeing emads snap has shocked a few of the guys into spending more time on

Mobility - rehab and prehab is up more than normal.

Edited by trentzor

Saw Jason this morning, have to go back on Thu after I get my X rays

he told me to stand in front of the mirror and showed me how crooked I am... it was ridiculous and weird that I've never noticed it before

he did say it's possible I have bulging or slipped disk but I think I'd be in much more pain... definitely no nerve damage which is good... lots of ice for the next 48hrs

hopefully the ice will reduce the inflammation, the x rays will be clear and some manipulation will have me back lifting in a week or two

he did say once he gets me straightened out I should see a strength increase

on a brighter note I benched 125kg x 3 for 3 sets... still on track for my first 3 plate bench press

That time of the year again. A few of my guys are riding that fine red line atm as they prep the final stages for nats.

Seeing emads snap has shocked a few of the guys into spending more time on

Mobility - rehab and prehab is up more than normal.

lol......no amount of prehab would save anyone from what happened to Emad

The operation is tonight, they are doing a biopsy on his bone to find the cause of the snap, as in disease, it has nothing to do with lifting weights, your humerus doesnt snap benching 110kg. It doesnt snap benching 400kg. It snaps if there is an issue with the bone.

I know mate lol. I should have clarified.

His was a freak accident.

Nothing could have prevented it.

It's pretty rare though I haven't seen such a break before.

Any specialist ideas on what caused it?

Plenty of guys bench for years without snapping it as such.

Keep us updated on how his going after op.

Edited by trentzor

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hello! I'm new here, I have an R33 GTST that is currently being finished up! Last year was pretty rough, blew two stock turbos so I decided to build the car. Has been down since November, but I get it back next weekend!
    • Hello, I believe my car was imported to America in the 2000s by Kaizo Industries. Would anyone be able to help me find more info on them? I've only found all the basic stuff like that paul walker bnr34, them being shutdown by feds, just stuff like that. Any help would be much appreciated, thanks!
    • I am using Motec M150.  I am not working on the car myself actually.  My workshop is giving all these info, they are quite reputable in the industry and are very familiar with Motec and RBs and have done a few big setups with VCam and single turbo on RBs.  In fact, they built and tuned my engine from day one.  But they are stumped with my engine at the moment and cannot work out how come the compression is so low with the VCam. They told me that they have now swapped in some Kelford cams (without the VCam) and can achieve around 130psi compression and the low end torque is better, but now the engine is doughy as.  It boosts and peaks at more than 1000rpm slower, with twin HKS GTIII RS, it doesn't get full boost until over 5000rpm. I have always thought the VCam was a bit disappointing at the low rpm. To a point I had to ride the clutch a fair bit to get up a small hill from stand still.  That was when I had a clutch.  Now changing to a 8HP, I don't have that luxury and this problem has become a major issue. I am beginning to think the VCam never work since the day it was installed.  Maybe it was just sitting at the most advanced point, that is why it went good at top end but very ordinary at the bottom.  Therefore, with the help of the Holinger 6 speed and paddle shift, as long as it was moving, it drove pretty good.
    • yeah, there's a country that recently started importing Skylines, I blame them.
    • I don't have a printer, but could at least attempt to make a printable model.
×
×
  • Create New...