Jump to content
SAU Community

Recommended Posts

I seacrched and found no definitive answer other than faulty coil packs of dicky AFM

Installed my power FC on my 34 GTT today in order to get ready for tune, I let the PFC by the 30min idle and so on.

Mods are:

Power FC

Turbo back

Splitfires

.8 plugs

FMIC

Apexi power Intake

Profec B

Walbro pump (hard wired)

Standard AFM

As soon as I started the car on the PFC the TCS and slip Light came on and stayed on, after the 30 minute idle self tune and a very slow run around the block all below 3000rpm as its untuned the lights wont go off. While driving the highest the knock ever got was 9 and everything else looked pretty good. On Idle the AFM was between 1140-1150mv

On a rev then after settling down a few puffs of black smoke came out of the exhaust and you can definitely smell fuel when idling but theres no puff of black smoke on idle.

With the factory ECU this wasnt happening, I have had the PFC running both on Standard R34 Intake and Power intake selections on the hand controller but still no difference.

Coil packs are splitfires and once again this issue was never present on the standard ECU, I only put in the PFC because its going for wheel allign tomorrow about 2 mins from my house and I wanted to put a rev limit on it so if they do need to take it for a run they really can't do much. I will be making them aware of this anyways its just a back up. Also the car will be sitting till dyno so might as well get it all done now.

I also had the Apexi Air Intake fitted to the stock ECU to check everything and no light, i have unplugged and checked the pins on the AFM connector and all good.

Anyone seen this before?

Edited by rb2534
Link to comment
https://www.sau.com.au/forums/topic/407575-tcsslip-light-on-with-pfc/
Share on other sites

Also running standard injectors, took it for another light footed lap after checking it all over again.

AFM around 1220mv

Timing peak hit 45 but was around the 15 on idle

The profec B is set to very low boost, I have never touched these and I am waiting to get this set up on the dyno so I have set it only for a few pound and it does have a hesitiation at around 3000rpm above if you very slowly drive it to those revs once again on light throttle. I put this down the fact that its the boost controller kicking in and the engine not getting much boost because the gauge will show only small amount of boost and the usual turbo flutter happens unless i short change it below this. On idle the Profec and boost gauge show a vacum between -400 to -600

It also idles rather high around 1100 even when warm and take abit to settle down to around 900-950, for example pulling up at lights it will hold revs then slowly go back to idle. A mate warned me about this and this has only happened since elimintating the BOV and running different turbo, after a big rev it will stall and most times go back to idle by itself but somtimes it will stall. Like all good mods i've learnt to mod my driving to suit lol

I know these issues will need to be sorted out with a tune which I am waiting for and the car does not need to be driven but I want to bring it to the dyno without any lights on or issues.

Once again thanks for any help

Just out of curiosity if it does eliminate it there may be a fault wth the PFC? I know ive had this PFC in before and these never came up. Also when I fitted the AFM this happen even on stock ECU so thats why I thought it was the connector this time but it appears to be all good.

I will refit it and see but I do have a brand new Z32 AFM here which I may just end up fitting if this continues

Cheers

Edited by rb2534

Started again with PFC in - lights on

Pulled AFM plug off, check and put back on - lights on

Removed PFC and put standard ECU back in, no lights

Put PFC back in and lights still on, sometimes they quickly turn off before they come in other times they stay on. really can't work this out as it has never done this before when I've had this PFC in. The only other thing have changed is going from a K&N pod to a Apexi Power Intake.I also picked both these 2 options on the hand controller and no difference and I'm sure it saved my selection.

Really out of ideas unless there is something in the PFC control unit that needs to be looked at with a laptop?

I took a pic also but the only things high lighted in bold are the dots next to the letters below, the black cirle only means the relays or switches are workign dont they?

IGN

ECC

A/C

F/P

O2H

ACR

img1575bg.jpg

Uploaded with ImageShack.us

Its a R34 GTT 4 door turbo, not sure what you mean about the Active LSD but I did read somewhere on a UK forum about traction control offline?? I couldnt find anything solid on it other than that statement though

I also held the up button on the handset to do that debug mode and all that came up were the letter "NT"

Edited by rb2534

boost if off - turned it on and the engine light came on, i turned it off and engine light turned off

air flow warning is on

injector warning is off (that made no difference)

knock warning is on

02 F/B control is off

This unit is second hand and has a map in there, i was thinking of doing a data init to start over and do the self tune but ive had this in my car before and these lights never came on.

The only difference between now and last time is ive installed profec b but and defi gauges and removed the factory 3 gauges. afm has been pulled off a few times to do intercooler and other work but as i said with stock ecu no lights

might be worth trying a date init and starting over

Edited by rb2534

Ive just noticed in settings i can set boost on the 4 steps but im not running a controller and i have the function switched off in the menu

settings are

1 .70 48 255

2 .80 54 255

3 .90 60 255

4 1.00 66 255

dontknow how this is but i did a data init, started all over and ther TCS/SLIP and Engine light came on, turned the boost controller function off and engine light went out but TCS and SLIP are still on. currently letting it do its self tune but i doubt that will change anything

Edited by rb2534

Did self tune and lights still on, removed PFC and plugged in factory ECU and everything fine and no lights so I think even changing AFM won't make a difference.

Still can't work out how I have a boost controller set up display that I can muck around and mod in the settings menu when I clearly have it turned off in the menu.

the boost control kit wont cause the slip/tcs lights to come on

the boost control settings are always displayed even when the kit is turned off

if the kit is turned on and not connected the check engine light comes on cos it cant detect the boost kit map sensor

that sensor sw check screen looks fine - if a sensor is f**ked the names goes bold highlight

black dots mean switch or relay is on - so all normal here

the only thing i can think of its the same as the ECR33 active lsd

where the lsd computer is expecting TPS signal from the stock ecu and becuase the PFC you are using doesnt do that, the SLIP/TCS chucks a spaz

have you got another friend with an ER34 you can check to see if theirs works?

has this PFC worked in your car before?

how does it drive? any misfire or other wierd shit?

form memory coil packs toast in ER34 turns on TCS/SLIP (no idea why) but thats what happens apparentyl

but its odd that its not on with stock ecu

this was what i had with my ECR33 and active lsd

stock ecu fine, powerfc Slip/Active LSD would always fail

Yeah as I mentioned the check engine light did light up and go out when i switched the boost controller on and off so at least that's cleared up. And if the boost display settings are always showing then that's fine.

I had this ECU hooked up in my car when I first bought it a little while ago and no lights, its just been sitting the cupboard waiting to go in right before tune, The only thing I have done in the mean time is hard wire and fit new in tank fuel pump, fit splitfires, .8mm plugs, boost controller, FMIC and gauges. I don't remember disconnecting anything other than the regular plugs and connectors to remove the dash etc.

With the PFC in I have only done about 1km of driving and not even gone over 60kmph so maybe the active LSD needs to hit speed or spin the wheel to work itself out or do some calibration thing. When I did hook it up I removed the AFM to do some other work and these 2 lights came up with is usual with stuffed coil packs or AFM fault. But I pulled over, turned the car off, pulled the AFM pug out, cleaned it and put it back in and restarted, drove then the lights went out. And the voltages are between 1100-1200mv on the handset, as I said I have a Z32 which i was going to fit and I;m still not convinced this is at fault.

As I haven't had it tuned I'm not driving it above 2500-3000rpm, it does have slight hesitation once it starts coming on boost but I've put that down to the Profec B boost controller kicking in as I have it set on stuff all boost until I get it on a dyno and can set it up safely. I also set an alarm on the Profec abit above the boost target and it reaches that so the possibility for a vacuum or boost leak causing a miss of hesitation when loading up should be eliminated. And once again it does it with the stock ECU and it free revs no worries, does not miss at idle and prior to fitting the turbo it went fine.

I'll have to put up a post to borrow someones 34 and check this out but this is most likely been dynoed early next week so i'll just wait til then and see how it goes on the dyno. As for anything else wierd on the car noting else sticks out, it idles, drives and does everything the normal ECU does so you could be right about the active LSD.

Did a fault code test on the factory ECU obviously , fault code 55 came up - No malfunction

Appreciate the help but until I get the dyno done there not much more I can do. I will update it once its done and see if is resolves itself.

Edited by rb2534

Did the fault code check and fault code 55 came up, Almost every forum says the two lights say coil packs or AFM, it has split fires installed and as I said the lights never come up on factory ECU, one would think the lights would come up on both ecus if there was a legit problem with the coils.

I'm going to remove the coil pack cover, check the connections again and I have a spare loom so i might bring that with me and go from there

Edited by rb2534

As I'm running smaller gapped plugs with near no boost this could be causing a miss maybe? Almost everyone I spoke to said run smaller gaps after about 1 bar, before that don't bother leave them at 1.1s

Im running .8s

Edited by rb2534

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah everyone always seems to refer to them as S13 wheels however they came on R32 Skyline, A31 Cefiro, C33 Laurel etc., and also came polished diamond cut or painted depending on the model. Congrats on your GTS purchase! I'd personally leave it NA.
    • In this thing about this 100% renewal energy stuff I hear no one really talking about anything other than power and fuel really Power and fuel, whilst being a huge part of how we use the billion year old Dinosaur juices, are only 2, of the probably thousands of things that we need to use it for in the chemicals industries for making nearly everything we use nowadays I'm all for a clean planet, but if we want to continue to have all the day to day appliances and stuff that we rely on everyday we will still need fossil fuels Whilst I do love science, and how it can bring innovation, there's really a limit to how far it can go in relation to "going green" As for EV's, unless your charging of your own solar panels, it isn't helping the environment when you consider the the batteries, the mining processes required,  the manufacturing process required, and how long a batteries (read: the vehicle) lasts long term If I was supreme dictator of the world, I would ban the use of sugar for fizzy drinks and food additives and use that for ethanol manufacturing, petrol engines would be happier, and people would be alot healthier  Disclaimer: Whiskey manufacturing would still be required, so says the supreme dictator of the world Same same for all the vegetable oils that get pumped into all our food, use that for bio diesel Disclaimer: the supreme dictator would still require olive oil to dip his bread in This would take some of heat off the use of the use of fossil fuels which are required for everything we use, unless you want to go back to pre 1800 for heat and power, or the early 1900's for plastics and every thing else that has come from cracking ethylene  Would I be a fair and just dictator, nope, and I would probably be assassinated within my first few months, but would my cunning plan work, maybe, for a while, maybe not Meh, in the end in an over opinionated mildly educated arsehole typing out my vomit on my mobile phone, which wouldn't be possible without fossil fuels And if your into conspiracies, we only need the fossil fuels to last until a meteor hits, or thermonuclear annihilation, that would definitely fix our need for fossil fuels for manufacturing and power issues for quite some time  Meh, time for this boomer to cook his lunch on his electric stove and then maybe go for a drive in my petrol car, for fun    
    • It really helps that light duty vehicles have absolutely appalling average efficiency due to poor average load. Like 25% average brake thermal efficiency when peak is somewhere around 38% these days. So even a 60% BTE stationary natural gas plant + transmission and charging losses still doing much better with an EV than conventional ICE. And that's before we get into renewables or "low carbon nonrenewable" nuclear which makes it a no-brainer, basically. In commercial aircraft or heavy duty diesel pulling some ridiculous amount of weight across a continent the numbers are much more difficult to make work. I honestly think in 5-10 years we will still be seeing something like the Achates opposed piston diesels in most semi trucks running on a blend of renewable/biodiesel. Applications where the energy density of diesel is just too critical to compromise. CARB is running trials of those engines right now to evaluate in real world drayage ops, probably because they're noticing that the numbers just don't work for electrification unless our plan is to make glorified electric trains with high voltage wires running along every major highway and only a token amount of battery to make it 30 miles or something like that after detaching. Transport emissions is not insignificant especially in the US, but yes there's a lot of industrial processes that also need to be decarbonized. I agree the scale of the problem is pretty insane but EDF managed to generate ~360 TWh from their nuclear reactors last year and this is with decades of underinvestment after the initial big push in the 70s and 80s. I don't think the frame of reference should be solar-limited. France is not exactly a big country either. Maybe it doesn't work everywhere, but it doesn't have to either. We just can't live off of fracking forever and expect things to be ok.
    • Yeah, all the crude is used for fuels and petrochem feedstocks (pesticides, many other chemicals, etc etc). But increasingly over the last few decades, much of the petrochem synthessis has started with methane because NG has been cheaper than oil, cleaner and easier and more consistent to work with, etc etc etc. So it's really had to say what the fraction either way is. Suffice to say - the direct fuels fraction is not insigificant. Heavy transport uses excruciatingly large amounts. Diesel is wasted in jet heaters in North American garages and workshops, thrown down drill holes in quarries, pissed all over the wall to provide electricity to certain outback communities, etc etc. Obviously road transport, and our pet project, recreational consumption camouflaged as road transport, is a smaller fraction of the total liquid HC consumption again. If you're talking aboust Aussie cars' contribution to the absolute total CO2 production of the country, then of course our share of the cubic mile of coal that is used for power generation, metallurgy, etc adds up to a big chunk. Then there is the consumption of timber. Did you know that the production of silicon metal, for example, is done in Australia by using hardwood? And f**king lots and lots and lots of hardwood at that. Until recently, it was f**king jarrah! There are many such sneaky contributors to CO2 production in industry and farming. NG is used in massive quantities in Australia, for power gen, for running huge water pumps (like, 1-2MW sized caterpillar V16 engines running flat out pumping water) for places like mine sites and minerals/metals refineries. And there are just a huge number of those sort of things going on quietly in the background. So NG use is a big fraction of total CO2 production here. I mean, shit, I personally design burners that are used in furnaces here in Oz that use multiple MW of gas all day every day. The largest such that I've done (not here in Oz) was rated to 150MW. One. Single. Gas burner. In a cement clinker kiln. There are thousands of such things out there in the world. There are double digits of them just here in Oz. (OK< just barely double digits now that a lot of them have shut - and they are all <100MW). But it's all the same to me. People in the car world (like this forum's users) would like to think that you only have to create an industrial capability to replace the fuel that they will be using in 10 years time, and imagine that everyone else will be driving EVs. And while the latter part of that is largely true, the liquid HC fuel industry as a whole is so much more massive than the bit used for cars, that there will be no commercial pressure to produce "renewable" "synthetic" fuels just for cars, when 100x that much would still be being burnt straight from the well. You have to replace it all, or you're not doing what is required. And then you get back to my massive numbers. People don't handle massive numbers at all well. Once you get past about 7 or 8 zeros, it becomes meaningless for most people.
    • @GTSBoy out of the cubic mile of crude oil we burn each year, I wonder how much of that is actually used for providing petrol and diesel.   From memory the figure for cars in Australia, is that they only add up to about 2 to 3% of our CO2 production. Which means something else here is burning a shit tonne of stuff to make CO2, and we're not really straight up burning oil everywhere, so our CO2 production is coming from elsewhere too.   Also we should totally just run thermal energy from deep in the ground. That way we can start to cool the inside of the planet and reverse global warming (PS, this last paragraph is a total piss take)
×
×
  • Create New...