Jump to content
SAU Community

Is 220Kw At The Wheels Powerful?

BOOSTBIG
 Share

Recommended Posts

vh45tt Contributor

vh45tt

Posted
Posted

My hr31 has a twin turbo vh45. With the new ecu and a really nice tune its making 378.9rwkw. And there is not a need for any more on the street. Much time has been spent setting up the spring rate on the coil overs and camber adj to get the power to the ground. Now i can get the whole 380rwkw to the ground from 3rd gear. It is stupid fast.

BOOSTBIG Contributor

BOOSTBIG

Posted
  • Author
Posted

My hr31 has a twin turbo vh45. With the new ecu and a really nice tune its making 378.9rwkw. And there is not a need for any more on the street. Much time has been spent setting up the spring rate on the coil overs and camber adj to get the power to the ground. Now i can get the whole 380rwkw to the ground from 3rd gear. It is stupid fast.

That is awesome bro. I can only imagine how fast that thing would be

to be honest man, I would be content with 300kw at the wheels. no more than that. as it is, its quick, but not quick enough to be content.

Tomorrow is the day I get a power tune done. will update you guys :)

boostn0199 Grand Master

boostn0199

Posted
Posted

Back when everyone mainly ran 98 300kw was considered a fast power that everyone wanted now with e85 in the picture 300kw now is like 200kw used to be its nothing special with most people at the power level now its 380 plus being considered fast.

BOOSTBIG Contributor

BOOSTBIG

Posted
  • Author
Posted

dude am I reading this correctly?

you've got a built engine but only standard injectors?

If so, you're missing out on some serious fun....

Yea man :(

short on cash. but it will be the first thing I get when I get some more cash.

WHITER33GTS-T Veteran

WHITER33GTS-T

Posted
Posted

Back when everyone mainly ran 98 300kw was considered a fast power that everyone wanted now with e85 in the picture 300kw now is like 200kw used to be its nothing special with most people at the power level now its 380 plus being considered fast.

420rwkw on pump fuel last year thru a auto :yes:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      The old manifold was quite under the GTR strut brace.  The new manifold is quite [unknown] the GTR strut brace. The GTR strut brace was needed to clear the bonnet vents. The Old strut brace will almost certainly clear the new manifold, but not the bonnet vents. The old strut brace will almost certainly clear the new manifold, and the new bonnet without vents. But I am hoping the GTR strut brace clears the new manifold :p
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Bonnet clearance?
    • joshuaho96
      Magnetic Drain Plug Snapped in Half

      By joshuaho96 · Posted

      On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
    • GTSBoy
      Finding E-30 & E-85 in Sydney

      By GTSBoy · Posted

      This seems like a pointless exercise. There is no E30 availability. Ongoing availability of E85 should not be assumed. Flex-fuel is the only sensible approach, so you can use E85 when and where you can get it, 98 when that's al you can get, and anything in between as you fill it up and drain it down. And if that means replacing the pumps, fitting a flex capable sensor/ECU/whatever has to be done to these Renault shitboxen, then.....so be it?
×
×
  • Create New...