Jump to content
SAU Community

Recommended Posts

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Rb25det Gearbox drove fine no crunching etc $1000

Front Bar $ 200 - Sold

Rear Bar $100 - Sold

Front LHS quarter $100 - Sold

Front RHS quarter $100

Front seats $90

Rears $45

Interior plastics From $ 10 just ask

Alternator $90

Ps Pump $90

Aircon compressor $85

Clutch Fan $ 70

Cluster $100

Carpet $ 200

Coil packs $20 each

Engine loom $165

Ecu $100

Suspension arms from $30 just ask

Seat belts $100 front pair

Stock bov with pipe $60 - Sold

Stock Injectors and rail $ 150

Fuel Tank $250

Headlights $250 - Sold

Taillights $120

Ps rack $100

Dash pad $80

Fuse box loom $150

Rear Subframe $165

Front crossmember $100

Door trims $50 each

Door handles $25each

Window regs $85 each

Power window switch drivers $85 Passanger $45

Window glass $75 each

Door skins $65 each

Hey mate what are the condition of the front seat belts? do they retract properly?

seat belts are are in great condition pm me if your interested so i can keep track please.

Do you have the out side b-pillar plastics? Both sides. " the little/ long plastic bit between the front and qourter panel window" message me on 0410717935 or pm me on here please need them ASAP

Do you have the out side b-pillar plastics? Both sides. " the little/ long plastic bit between the front and qourter panel window" message me on 0410717935 or pm me on here please need them ASAP

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Dose is unaware just how much fun 145-150kw would be in a 2.5L NC MX5. It would be one of the most fun things to drive to ever grace SAU.
    • Same thought crossed my mind ~ depends on how one connotes 'stalling'...ie; gets a rough/stumbling idle as it get warm until it stalls... or... idles ok and simply falls-over when it gets to temp... ...you can test the whole circuit with a couple of resistors ...unplug coolant temp sensor, bridge terminals with a 2K7 resistor (ECU will do cold start), or with engine warm bridge with a 330R resistor (ECU will consider engine to be at normal operating temp)...it's a quick way to check wiring integrity/ECU response when you don't have a multimeter handy ...
    • They also make them with the motor mounted on the side 
    • Just be warned that that turbo will not be a direct re-fit to the car. The exhaust housing is, of course, in the same place. It has to be - it's bolted to the exhaust manifold. So the dump will fit up. But the centre housing is not as long, so the comp housing will move backwards. This will affect both the turbo inlet and the outlet. There is fab work that needs to be done. Yes. it has one, it should have one. Paper gasket.
    • I only recently purchased the vehicle, it came with the flex setup but the current tune is e85 only, which is why im wanting to get the tune redone to enable a mixture.  First i need to get the exhaust redone tho. I was thinking of getting a varex muffler but it sems they dont fit well in the 33 (hang low because of the valve mechanism which sticks out on top) and generally dont sound good. So that leaves me with redoing the entire exhaust (more resonators and mufflers) so its not a menace when i come and go from home, and then have the aes dump valve somewhere along the line to really open it up. I was thinking of having it before the cat but after seeing how insanely loud it will be (on a vl turbo) im thinking of putting it more towards the rear of the car, after one of the resonators. 
×
×
  • Create New...