Jump to content
SAU Community

Recommended Posts

hey guys

i have been looking into this for quite a while, and im about ready to give up, i hear alot of cars having alot of flutter etc when changing gears etc...

and alot of people have been saying it the blow off valve, and alot of people are saying its turbo/compressor surge. just wondering which one it really is.. because hell i think it sounds cool, and would really like it on my r34. and if it is turbo surge, some also say its fine and some say it bad etc can anyone give me some more insight please?

any opinion and help woule be greatly appreciated

Conz

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/
Share on other sites

It is compressor surge and is caused by the bov. When the bov doesnt open at the right time or doesnt open enough the compressed air flows back across the blades of the turbo and out of the air/pod filter. This is often because of the spring rate in bov. It is not good for the turbo because the blades can get damaged and break and go through the engine. The flutter may sound cool between gear changes but its not worth it.

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6520961
Share on other sites

The R34 has a nylon compressor wheel which makes them lighter and quicker to spool... yet weaker under high psi/temperature. They're only good for about 10psi and are probably one of the worst turbos to experience compressor surge with. You could get the factory turbo hi-flowed, where they replace the inlet and exhaust wheels with steel. But even so, I wouldn't recommend compressor surge on any turbo.

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6521860
Share on other sites

There's a few different forms of surge most common is when the throttle and bov are closed while boost is still in the system with no where to go and it back tracks to the comp wheel and trys to stall it while the turbine is still being driven making that lovely flutter sound which is very bad for the turbo. It puts over 100 lbs of load on the thrust bearing which only has a 2mm contact area in some cases and so they fail quickly.

The other type (shown in the video) is a mismatch of compressor wheel in relation to setup as in its outside its efficiency zone or surge limit and it cant grab air to make boost if it gets to bad it can have a servere enough effect to brake cranks or engine mounts.

Pretty much most blow valves on the market today are crap inducing surge when the stock one worked perfectly fine there is others ways to do systems that dont need a blow off valve - red top RB20's/rb30 VL

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6522997
Share on other sites

This topic comes up once every couple of weeks, use the search function.

People are usually divided when it comes to whether turbo flutter is bad or not. Some people have been running fluttering turbo's for many years with no problem, others blow turbo's and quickly blame turbo flutter when it could have been many other reasons.

This is just my personal opinion, I have had a slight flutter on my ceramic turbo R34 at 12psi for 4 years now with no problem at all. I have read recently the smaller turbo's don't have the surface area that back pressure can damage as easy as larger turbos as the larger blades would be more susceptible to shear forces, but then others say the flutter in smaller turbos is dangerous. Whatever.

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6526852
Share on other sites

No one knows for 100% sure if it damages your turbo-charger. It is nothing more than a speculation.

All you have to do to get the sound is block off your blow-off valve. Instead of the air venting via the blow-off valve, it travels back through the intake across the blades of the turbine spinning forward. The resultant noise you hear is commonly referred to as flutter.

Don't listen to most of the tools here saying not to do it. If you like the sound, then do it. Nothing more than personal preference.

As stated, no-one can prove if it actually damages the turbine blades. XR6 Turbo Falcons do it from factory with nothing more than a pod-filter - you do not need to close the blow-off valve.

My brother had an R33 making 450rwhp, running a GT35R and a closed blow-off valve for the flutter sound. No problems ever reported there and that was over the course of 75,000km's.

It's quite simple; if you like the sound, do it.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6527641
Share on other sites

I had a few skylines one with a 35r forged engine etc and blocked off bov because the sound annoyed me had no dramas!

Also stock 25 with a 3076, blocked and that's still going with no dramas! Personal preference but on stock turbo set ups not worth it!

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6527764
Share on other sites

I tell people not to listen to the tools who tell them its ok to do it on their cars which cost them xx thousand. But what do I know? I happen to get my information from people who rebuild turbo's for livings and not off google.

So what if it didnt happen on your car, it may happen on his. And if you want to be the idiot who told him it was ok, thats on you.

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6534212
Share on other sites

I tell people not to listen to the tools who tell them its ok to do it on their cars which cost them xx thousand. But what do I know? I happen to get my information from people who rebuild turbo's for livings and not off google.

So what if it didnt happen on your car, it may happen on his. And if you want to be the idiot who told him it was ok, thats on you.

good to know u get your info from people in the loop but gathering information and having it on your car is a different story, like i said, personal preference, your car do what you want!!!!!

his is stock, my set up was aftermarket and yes im the idiot who blocked my bov, BOO FU**ING WHO

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6535611
Share on other sites

  • 4 weeks later...

Meh, BOV sounds are good for one thing and one thing only, creeping up to bus stops when school finishes and all them kiddies are standing around, then as u get closer, boost it hard and blow it off righttttttt next to the bus stops. Hks SSQV/ Turbosmart Supersonic <3

Link to comment
https://www.sau.com.au/forums/topic/408651-bov/#findComment-6571668
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks again, really helpful chap from alpha omega wanted to speak to me, little concerned if this is meant to he aero alloy/ airospace quality and car sitting on drive has caused this.  Airplane are subject to much more changing temp and conditions than road salts! My caliper, many other components much older have surface rust but never eating part of the metal   Had I not seen it , could have been a disaster! specifically on rear part of bracket coming off like biscuit will update on what they say, helpful people so far
    • January or Feb is it booked in for turbo fitment?
    • The MX5 has had some annoying rattles in both front doors over bumps So I installed fancy pants door bushings, which stopped all of the rattles with the windows up, but........with the windows down there was still rattles, so after some googling,  and a chat with MX5 Mania, I got some new door to glass weather seals, all the rattles, windows up, or down, are gone now Shout out to MX5 Mania, the weather seals were on sale, and when I head to Dural to pick the up they even fitted them for me for free I did see a "really" nice Blue NA sitting out front   and this Black NC PRHT that looked like it has sat in the sun for its whole life and never had a wash, the clear coat was non-existent, an it looked horrible, really horrible, but, it had a nice turbo kit with over 200kw, the thing went like a cut snake, bagging the rears through the gears and dosing like a champ 😍 But, as I've always stated, I am keeping my NC na, I'm happy with the current power the car makes In other news: MX5 Mania do a drive in drive out turbo kit, the only minor additional part recommended for boosting my car, as it sits now, is a oil cooler, and that bonnet vents are definitely required for track use Aftermarket version look a bit to "racecar" spec I wonder how Focus RS bonnet vents would look?????
    • Paint is only structural when applied to the outside of Chinese and Indian cars. Otherwise it should never be present between mechanical joints that were intended to be metal to metal. Pain slips, slides, cracks, compresses, and add thickness that wasn't intended to be there. It comes firmly under the category of "just no".
    • appreciated it thanks   There are threads on the adaptor. I rear re anodising but didn’t know it will reduce strength   re mating services needing to be flat/ not painted, why would that be? I am devastated as car been off for a year, fixed power steering then installed bm57 master cylinder and just before driving it this came up. So annoyed   worried and afraid to drive it, no fun caliper coming off    
×
×
  • Create New...