Jump to content
SAU Community

Recommended Posts

you guys making over 300+kws with standard oil pumps or are they aftermarket?also ARC are the best flow on the market.

I dare say most of the motors making that power are unopened and have never come out hence running standard oil pumps

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

In the new PI magazine, the r32 gtr "gmaster" made 360kw with stock r32 cooler, then changed to an r34 cooler and made 380kw, then again changed to a cooling pro 76mm core and made 411kw....

All runs done on JEMs Dyno...

51 KW gain for changing an intercooler- Id like to see the graphs. Also would like to know if the gtr cooler was in good nick.

As for the XR6 cooler debate its really not a fair comparisson putting a 4L I6 next to a 2.6L I6.

The Barra can push out 320rwkw out of 12psi with not too much difficulty. Compare that to the conventional 18 - 20psi to get the same power level out of your typical twin setup RB (purely going by the results I have seen in the RB26 Dyno thread in the past).

A RB30 will need 17psi for the same power as a RB26 will @ 20psi (for example) - it's still the same amount of air, there is just less restriction (boost). It's as much about the volume & cooling that volume as it is about the pressure. Both need to be taken into account....

And it's totally fair, it's and intercooler. If it's tested to flow fine @ 25psi+ and does the job - then size is irrelevant, this is why i was going to use one :thumbsup:

sorry was this on BP pump or E85 / Water meth??

BP Ultimate ususally

you guys making over 300+kws with standard oil pumps or are they aftermarket?also ARC are the best flow on the market.

N1 here (3 times). But thats a whole different debate, search and start reading for that

The core Nizpro use for their XR6 upgrades flows enough for 400-450rwkw and these cars are well proven. From memory it's roughly:

400mmL x 300mmH x 76mmD

Now look at a Greddy replacement size:

600mmL x 284mmH x 76mmD

If Nizpro cores that are pretty much the same size as a GTR core (GTR is actually larger)... and they flow easily 400rwkw... I don't see why it's so hard to believe a GTR one, or sized replacement, can't?

The Greddy GTR core is smaller (in internal flow area) but has longer tubes. Ergo, it will have a higher pressure drop. So I would say that raw cooling ability aside, the GTR core should be flow limited to a lower power ceiling than the Nizpro XR6 core.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A little more work this week.  Fitted astra power steering pump in the boot with a lowe fabrication bracket. Gave the pump a good clean, fitted Anderson plug and high pressure fitting. With the intercooler being flipped under rad support factory headlights weren't going to work. Ordered a set of origin battle lights, they arrived so got them test fitted. Will require some fiddling to fit nice but was an easy quick option for now. And today we pulled out the manual Rb gearbox and test fitted a ZF 8HP50. It will fit with some casting tabs cut off and small tap of the tunnel with a hammer. Pick up the adapter plate Wednesday so hopefully all bolted in Friday and measure for tailshaft which will be a 2 piece. Been doing a lot of ecu, pdm and tcu loom design so when comes to wiring it in a few weeks will all go smoothly.
    • FYP. Sadly. Even bolt cutters wouldn't take 2 sec. But in the days of 18v angle grinders, nothing is safe.
    • One piece driveshaft I would recommend a dual CV setup otherwise stick to OEM. I have heard most one piece driveshafts cause excess vibration otherwise. The transmission grind I'm quite familiar with. You can try shockproof gear oil, otherwise you need a new transmission. The shifter is extremely simple on these cars. If you want pull apart the assembly and replace the plastic bushing but I doubt that fixes anything. The tail light issue is very common, unfortunately new tail lights are long discontinued. The trunk antenna going up always is because your radio doesn't have a true power antenna control, just remote amp power signal. There is a blank switch plate that you can pop out and install a switch for this or alternatively source a head unit that has proper antenna control. Throttle body sticking you have to disambiguate by disconnecting the cable and seeing if the linkages are the problem or something else. There is a procedure to adjust them, refreshing them is also somewhat involved if that's the issue. I have dealt with many of these issues. Old cars really are fractals of problems. The more you fix the more you discover there is to fix.
    • Welp, you've got a long list of experiences right there. I'd say you're on the right path.
    • That's correct, suits my requirements a bit better. Sure there are also numpties there, however it's generally a different vibe and more my kind of vibe.
×
×
  • Create New...