Jump to content
SAU Community

Jecs Injectors Size, Leaking Injector

boardman

By boardman,
in Engines & Forced Induction

 Share

Recommended Posts

boardman Contributor

boardman

Posted
Posted (edited)

hey guys had a leaking injector that i pulled out today. going to replace all the o rings on them. 2 questions. should i do anything more then just replace the o ring to stop leaking ive heard they leak alot. and can anyone confirm the size of my injectors. numbers i found on the injector are:

jecs

A46-000001

5L31 2827

injectors are in a rb20det

Cheers Adam

Edited by boardman
The Dan Grand Master

The Dan

Posted
Posted

hey guys had a leaking injector that i pulled out today. going to replace all the o rings on them. 2 questions. should i do anything more then just replace the o ring to stop leaking ive heard they leak alot. and can anyone confirm the size of my injectors. numbers i found on the injector are:

jecs

A46-000001

5L31 2827

injectors are in a rb20det

Cheers Adam

I think I've got a couple of dozen laying around if you want some. You can have them

boardman Contributor

boardman

Posted
  • Author
Posted

Never mind I just read your info haha. Ill try these seals out first and see how they go if it is the injector we will organise postage and stuff. Should I be putting anything extra on it to seal it up like silicone or just the o ring.

The Dan Grand Master

The Dan

Posted
Posted

Never mind I just read your info haha. Ill try these seals out first and see how they go if it is the injector we will organise postage and stuff. Should I be putting anything extra on it to seal it up like silicone or just the o ring.

Rubber grease the oring on top but not on the bottom of the injector. Reuse the spacer at the top.

If you don't have rubber grease, vasoline works also.

Buy the orings from Nissan. Non genuine ones aren't the same size always

boardman Contributor

boardman

Posted
  • Author
Posted

i replaced the o rings today couldnt get genuine ones from nissan but went to a injector place and he gave me 6 new ones. put them in and the same injector is still leaking. looks like its the actual injector that is leaking not the seal so i will need a new injector. Daniel ill pm you and see what we can sort out cheers

StevenCJR31 Veteran

StevenCJR31

Posted
Posted

There is no hose going into it. That's Rb30.

Mate, pretty sure I can get them to you for $15 freight or wherever you are.

I'll clear my messages so you can try sending me your address

yep, sorry you are correct, the 30E is top fed hose and the 20DET rail sits right on top of the injector with a rubber seal

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Import insurance in 2025

      By Kinkstaah · Posted

      The max they would go for me is 50.
    • Duncan
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By Duncan · Posted

      That cannot have been a fun set of drilling. The stock "baffle" looks identical to rb26, I just cut fuel cell foam to fit the full length under the baffle.
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

    • GTSBoy
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By GTSBoy · Posted

      I understand your sarcastic exasperation. But to be fair - the baffles do indeed fit OEM cam covers. They did omit to say that you need to do a bunch of stuff. But they do fit them.
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      Got started on the modification to make these splash plates fit over the long weekend. First the surprisingly time consuming task of swapping all the cam cap bolts to Tomei cam cap studs. I did the method of removing one bolt at a time, applying loctite to the stud, double nutting to torque as the manual described. Then carefully unlocking the nuts without disrupting the torque of the stud (and going back to re-torque a few times when it slipped). Finally applying the nut and torquing to spec. Repeat x28 Next up I went about removing the stock cam cover baffle so I could ensure it was fully clean after drilling for stud clearance.  As the blind rivets holding the baffle on were domed I used a punch to mark the center then used 4mm drill bit to carefully drill out the rivet without going too far part the baffle. As seen in other thread here is what is inside the stock baffles I decided on M4x6mm bolts to bolt the baffle plate back on with. I used a 3.3mm drill bit with some tape to mark the depth at ~8mm. Next was to tap the threads using a cheap bunnings kit M4x0.7. With the baffle removed I also drilled out the spot welds holding in the baffle plate oil returns. Unsure whether this was the best option or if I should have cut holes in the Hypertune splash plates to allow the oil drains to still function... time will tell. I then removed the the Hypertune splash plates so I could rest the cam cover on top and use a dab of grease to mark where the studs impacted the oem cam cover baffle. The most obvious spot was on the hump from the stock mesh is held. Using this hole as an anchor I bolted the oem baffle plate back into the cam cover and lined up the Hypertune splash plate. Marked the rest of the holes for the studs and drill those out too. Total 32 holes drilled and 12 threads tapped on the passenger side cam cover alone for this bolt on part that totally clears all OEM cam covers.. Drivers side next as well as some E85 safe fuel foam to fill the space behind the behind cam cover baffle plates. oh and some lock nuts for the splash plates of course.
×
×
  • Create New...