Jump to content
SAU Community

Recommended Posts

HKS Type S oil cooler kit to suit rb25

This has a thermostat built into the adaptor housing.

I bought this brand new in Jan, has been used for 1 hill climb and that's it.

Like new condition, comes with the original braided hose in perfect condition.

$500

This is the kit

http://www.nengun.com/hks/oil-cooler-kit-type-s

In Syd

post-3412-0-28730300-1347683278_thumb.jpg

post-3412-0-92127400-1347683307_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/409338-hks-type-s-oil-cooler/
Share on other sites

Does this have 1/8npt threads in the sandwich plate for pressure or temp sensors? If so I will be super keen and sell my Trust kit I just bought for this as my kit has a relocator and r34 engine bay has no room to fit the relocator.

As I dont want to relocate the filter I was opting to buy a sandwich plate and set it up the same as yours but this will save me a heap of time.

Edited by rb2534

If you can confirm it then I'll most likely take it

the industry standard for passenger vehicles worldwide, usually confroms to 1/8 national pipe thread (npt) for sender units, water and oil. if not, i am sure you could find an adapter / reducer from your local purple pig, hose doctor, enzed etc, shop for about 5 bucks, it shouldn't be an issue. if it is, i'd be glad to help you out even if i have to make the bastard myself!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This has been covered a bazillion times but google wet boiling point vs dry. Motul is only good when it's fresh, once it absorbs moisture it gets pretty average very quickly. So as above, make sure you change it if you're going racing. I run the Endless brake fluid in mind, but only because a mate is a distributor and it's cheap. It's not quite as good as SRF but I'm running 380mm rotors on a Skyline so it's not like they get hot.
    • That's the thing, they still add it and it makes fuel cheaper, implying adding 10% of it drops the cost of 91 by what, 5c a liter? I remember when it was barely half the price of 98. Because you know, 85% of what is in the fuel is way cheaper than 91 fuel is by volume.
    • Auto electricians that do repairs on automotive AC systems can source service kits. I don't know where they actually source them. I do know that there is one available for the R34 comp that I would need it for. If you have to pay someone to dismantle, clean and do needed repairs and fit kit contents, then you'd probably end up spending a good fraction of the cost of a new one. I would not be paying for that, because I would be doing it myself. My mechanic (bro-in-law) will happily source what is needed. Back in the day (like in the 80s and 90s), rebuilding an AC compressor was the standard approach, same as for starter motors, alternators, etc, because new replacements were v. expensive. After the China manufacturing boom and the rise of the disposable approach to everything, people just started throwing broken/worn stuff away and not rebuilding things.
    • Is rebuilding it even a thing? Where would the shop find parts for it? I looked at some off these local online stores for my r34 and suprisingly they had brand new aftetmarket ones for $600-800 I think. I guess r32 might be a bit tougher.
    • I remember the days when E85 was priced in according to the $ per km outcome. Sure E85 was about 35% cheaper, but you also lost about 35% range... now it's fked..
×
×
  • Create New...