Jump to content
SAU Community

Recommended Posts

I've been reading through a bunch of threads with similar issues yet nothing that directly relates so far.

If have a BNR32 GT-R and it's been a long cold winter here in Melbourne and the car felt like it was running fine and smooth the whole time. As there's been few warm days recently its been causing the car the run with rough idles and almost stalling at times. It will only happen if its on a warm day of more than 20 degrees.

I've also noticed that the engine check light will flash at times and then be ok again but other than that car will boost ok and give off consistent power.

So far I've read that it could be one of the vacuum lines in the plenum or the timing itself. My guess is that it could be the AFM's or sparkplugs. I am running stock AFM's with an ARC Airbox.

I also took it to be Dyno tested to see if the issue could be replicated but they found nothing aside from it running slightly hotter than usual after load. I am running an aftermarket radiator as well. However it was fairly cold day so it may have been easily spotted.

Was wondering if anyone else has had experiences with this and any suggestions would be appreciated!

Anytime the engine light flashes, the ECU will store that error code until you either clear it via CONSULT or disconnect the battery. Either read the error flashes from the ECU, or get yourself a CONSULT cable or one of these: http://ecutalk.com/consultlcd.aspx and grab that error code.

When were the spark plugs last changed, and what type are they (copper, platinum, iridium etc).

Can you hear any hissing (vacuum) in the enginebay while idling?

If you spray something with alcohol (wd40, brake cleaner, aerostart etc) around the intake manifold, ITB's, vacuum hoses does the RPM (engine changing note) temporarily rise?

Things that go wrong when hot but work fine cold, generally don't rule out the coilpack ignitor or the crank angle sensor. Until you get that error code, it's all guesswork and you might even be on the wrong track.

Thanks for the suggestions there. I'll go down the CONSULT route for now and see what its telling me first.

Sparkplugs I'm running are just NGK Platinums but I don't remember the gapping of it. But they are almost 2 years old now so may need to pull them and check. I changed the coilpacks a few years ago to Splitfires so I somehow doubt that would be it. :-/

Can't hear any hissing or vacuum leaks so far but will check further there but I haven't tried the WD40 with the intake manifold yet but if RPM rises for a bit is that a good sign?

thats the sort of thing that was happening when i had a intake manifold leak, was fine til it was at operating temp, got worse every day

the leak makes it run lean and thats what makes it rough and stall, but the opposite happened on full throttle, id get some big black clouds out the back, fill up half the street ..also seeing boost but not feeling the power for a few seconds cause it was blowing out the manifold... any of that happening?

Edited by SliverS2
  • 3 weeks later...

Manifold leak I'm still investigating as it seems to run ok 90% of the time.

Since its been getting warmer recently I've noticed it happening more often and I can sort of replicate it if I deliberately try to stall it where it will take over and try to keep the revs up. It will then start 'hunting' for up to 10-15 minutes afterwards.

Cruising along at constant speed it will feel erratic during that time.

I'm starting to count on the AFM's needing replacement in this case.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide 👍
    • Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • Have you looked at the workshop manual?
    • Hmm. I've gotten pretty good outcomes from talking to them about things that I've had go wrong or ideas for improvement. Have had a lot to say about the R32 FUCAs, and they have sent out some replacement parts for those, gratis, on a couple of occasions. Mind you, I have bought a couple hundreds of $ of replacement rod ends for them too!
×
×
  • Create New...