Jump to content
SAU Community

Recommended Posts

since last night I bad rattling noise as emerged from engine bay...Its definiately not the dash.

I find I can make the sound worse if, I put into gear (i.e. first gear) and release the clutch to the point of friction where it lets go, without putting pressure on the accelerator pedal..

ANy ideas? This is worrying me....

Link to comment
https://www.sau.com.au/forums/topic/41004-help-major-rattling-noise-on-s15/
Share on other sites

Na it will be ten VVT my friend. My S14a does it and nearly every S14 i know and some S15s that have a few more K's(not Many though) do it. Common problem. Cost around 1500 to fix, not really worth doing as it doesnt really cause any problem. If the car is still under warrenty get it fixed, he he.

its hard to varify what the noise is exactly without hearing the noise coz some noises sound quite similar, but u say u can make it worse when selecting a gear but the noise goes away when u engage the clutch abit in gear? Possibly an internal gearbox drama, mainshaft bearing/s, counter shaft bearing/s something like that, but again unless i know whats actually happening and when, with what noises etc its hard to tell u, ur best bet is to talk to someone in person(ie a mechanic or gearbox place) and see what they say. U could try talking to boosteds15 of www.boostcruising.com he has an s15 which has had afew gearboxes replaced. maybe u have the same drama

my s15 has done 28000kms. and it doesnt happen when i rev the car or while normal driving.

i agree sweetr33 sounds a gearbox problem....ICE in melb says its possibly the thrust bearing. Pain the in arse to change cos u gotta take out the whole gearbox....

I can make the noise appear by putting into 1st gear, then slowly disengage the clutch to the point of friction where I nearly stall. By the way this is when NOT pressing the throttle.

could it also be the engine/gearbox mount?

I know i might be repeating the people above but it really sounds like a thrust bearing issue had a similar problem on an import gemini, turned out the spring that holds the bearing had come off and lodged itself between the fork and bearing, thus always making it touch the pressure plate.

Mind you my problem ended with a screech squeel yelp and than bang as the pressure plate disintigrated the thrust bearing, in amongst other things.

Pull of the g/box and check it and its not that much of a bitch if you gotta pit/hoist.

there is 6 bolts holding the box on the bellhousing 4 holding the tail shaft 4 bolts mounting the box disconect the slave cyilinder and yank out the shifter.

Ohhhh and don't forget to drain the oil.

ooo and trhe starter motor 2 bolts holding that one

Hope it helps

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Also had a look at the Nissan JP website looks like the 400r has a slightly shorter ratio than than the regular V37 3.133 VS 2.937 which from a guy who has driven both 3.69 vs 4.11 ratios in the S15 is bugger all. Seems that the AUTO Z runs the same ratio as the 400R but can't find any info as to if its an open or LSD? More often than not the auto LSD is open
    • Do not replace the power steering lines with this stuff. If it's anything like the Chase Bays stuff it will leak and be worse than stock. The reason why the reservoir is on the LH/passenger side of the car is because that's just where the reservoir was most convenient to fit. Don't overthink this stuff. The intake/cold side of the engine is pretty busy on these cars. And again, the hardpipe is designed to be a janky power steering cooler. In theory you can replace it with a real power steering cooler but that's really only for track use where boiling the fluid is a distinct possibility. Start with the low pressure lines feeding the pump from the reservoir. Make sure there isn't a bunch of junk in the reservoir filter. Be careful to not get ATF all over the engine bay. I hate dealing with ATF spills, you can clean it up and the slightest crevice will still release more oil that can still drip over time. You also want to inspect for leaks before you make a mess and can't tell what happened. Most likely you have a leak somewhere that is allowing fluid out and air in. Failing that it's allowing air in but not fluid out. Only place I can really see that happening is on the low pressure side because the pump will pull a slight vacuum to draw fluid in. Everything after the pump is high pressure or lower pressure, approaching atmospheric by the time it returns to the reservoir.
    • I did a skidpan night at SMSP this week, it was much cheaper than $350. But yeah, you need to slap an LSD in that thing.  I put an OS Giken in the 370Z and it's f**king MARVELOUS even compared to Nissan's viscous LSD. So you're saying it's free now that it's a housing estate? 😂
    • Nah, the car seems to run exactly as it did prior, in saying this it does "seem" to be better down low, like more eager to rev, but that may be 100% placebo effect from intake noise But, I'm not worried about it at all, in the end it is a fairly low compression NA engine that has a well shrouded intake,  if it is getting hotter IAT I cannot notice anything negative performance wise from the seat of my pants thrashing it about on the street or sitting in traffic, so meh, car now now makes induction noise so I'm happy
    • Do you have an IAT sensor? It's worth checking it to see. You may be suprised how little gap you actually need to flood your engine with hot air. (I tape up my airbox for a reason) :p
×
×
  • Create New...