Jump to content
SAU Community

Recommended Posts

Hi guys,

I had my R34 over the pits today and got reamed by an inspector who obviously did not get laid the night before.

As a result I have an inspection list with "VSS App required" next to a few items, including coilovers, intercooler, pod filter, trailing arms, castor rods and steering box/rack.

What is the correct proceedure to get these accepted? Do I have to fill out the Modification Application first, then get engineering certificates? Or do I get engineering certificates straight away?

I'm confused, and the rude inspector walked away without allowing me to ask any questions

Link to comment
https://www.sau.com.au/forums/topic/410047-car-mod-permit-question/
Share on other sites

I am in the process of doing exactly what happened to you

You need to submit the application for mods straight away

Wait 2 weeks and they will send you a form which lists the things they need from the engineer

Submit engineers certificate and wait another 2 weeks and see how it goes

Meanwhile your yellow will run out and you'll have to get an extension which means another pit inspection

Feel free to call me

I can give you a really good engineer and some tips as I have been through the reaming machine and now know the process

Grant 0413775441

pod filter is easy change

either mount it securely or go back to an airbox

coilovers

farking farkedy fark fark

no need for permit - its not even yellow stickerable UNLESS they are wound too low

suspension mods in general are fine GIVEN that they are made for the car that they are going into and are a replacement part (ie s13 coilovers INTO an s13)

heim jointed items also from my understanding need to be engineered (or at least looked at by engineer) because there is no compliance in the device and could cause binding (or some shit like that)

intercooler - im not sure if it has to be engineered - but i believe that if there is no cutting of the bumper reo you *should* be fine

if all else fails - read the National Code of Practice documents in relation to vehicle design and modification

NCOP11_Section_LS_Tyres_Suspension_Steering is the document you want for the suspension stuff

Thanks 342four.

I'm thinking of leaving the pod and fmic and submit them in the application for mods and hope for the best. Getting the fmic out will be a pain. The pod is secured already but they still requested application for it.

Hopefully the fmic and pod won't need to be engineered.

  • 2 weeks later...
  On 12/10/2012 at 2:51 PM, Everlong-S13 said:

Was it a simple modification permit form or full engineering check?

Engineers report was required for pod FMIC and aftermarket struts (with camber adj arms)

But they were giving me the full treatment after I gave them some backchat and a burnout, so you may be lucky.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...