Jump to content
SAU Community

Recommended Posts

No. If you read what you yourself have written, you will see that the act of drifting requires a lot of longitudinal drive force to be expended to make the car want to follow a curve for which its corner entry speed is too high.

Brute force over elegance.

No. If you read what you yourself have written, you will see that the act of drifting requires a lot of longitudinal drive force to be expended to make the car want to follow a curve for which its corner entry speed is too high.

Brute force over elegance.

i think you just said a whole lot of words without really making sense. you might be thinking of powersliding, but you don't need bulk longitudinal drive to drift, a lot of drift cars dont have much of it, but the good thing is if you do have it, with drift you can use it to steer the car as the whole car is pointed towards the exit of the corner as opposed to even your most wild slip angle a grip car might carry where the rears are still pointing and pushing you towards the outside of the corner (ie not where you wanna go).

drift is the very essence of car balance, the fact that it's been basterdised into barely more than a powerskid comp in some areas of the world doesn't take away from the fact that the sport was formed in cars which didn't have enough power to even do a standstill burnout, they used careful weight shifts and well placed line to continue a drift.

i think you just said a whole lot of words without really making sense. you might be thinking of powersliding, but you don't need bulk longitudinal drive to drift, a lot of drift cars dont have much of it, but the good thing is if you do have it, with drift you can use it to steer the car as the whole car is pointed towards the exit of the corner as opposed to even your most wild slip angle a grip car might carry where the rears are still pointing and pushing you towards the outside of the corner (ie not where you wanna go).

drift is the very essence of car balance, the fact that it's been basterdised into barely more than a powerskid comp in some areas of the world doesn't take away from the fact that the sport was formed in cars which didn't have enough power to even do a standstill burnout, they used careful weight shifts and well placed line to continue a drift.

For my ten cents worth I think there is a common misunderstanding that alot of people have.

Put correctly any tyre that is producing lateral grip is generating a slip angle.

Also steering a car on the throttle is a common technique in just about all forms of motorsport.

It is still common to see cars pointed well inboard of the apex of the corner due to the slip angles generated by front and rear tyres. Admittedly not as much as the olden days when slip angles used to be much bigger but enough. It is most pronounced in low powered categories with no downforce eg the formula vees and fords do it alot.

For my ten cents worth I think there is a common misunderstanding that alot of people have.

Put correctly any tyre that is producing lateral grip is generating a slip angle.

Also steering a car on the throttle is a common technique in just about all forms of motorsport.

It is still common to see cars pointed well inboard of the apex of the corner due to the slip angles generated by front and rear tyres. Admittedly not as much as the olden days when slip angles used to be much bigger but enough. It is most pronounced in low powered categories with no downforce eg the formula vees and fords do it alot.

at large radius corners with high G's and big slip angles, yes your rears will be pointing towards the exit, but like i said, with even the most wild slip angles, on tight radius corners your average grip car isn't coming anywhere near the rear wheels pointing towards the exit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for the reply @GTSBoy this is is a hydraulic lifter engine. Yea right i did not realise the lifters were supposed to be compressible while installed. I could push them down but i had to lean almost my while body weight on them.  I have never heard of a lifter/ lifters ticking only at hot idle and getting worse the hotter it gets. I have owned a few jdm cars with noisy lifters. This noise is slightly more subtle, it is more of a sharp gentle metalic tic than the solid and more loud tapping I've heard on lifters. I have used a metal rod, alloy tube, hose and stethoscope and could not find the source of the tick. But it appears to be loudest on the actual engine block behind the exhaust cam gear and next to the oil filter. I had mate (40 year old mechanic) go over it with me and he couldn't find it either..  Could it be a cam seal issue of some sort?  Cheers  
    • This seems problematic and unlikely at the same time. Vanilla RB2Xs have hydraulic lifters. They do have "zero" clearance, but only when running with oil pressure inside them. When not running, you should be able to compress them and obtain heaps of clearance. RB26s and Neos have solid lifters. They should have ~0.3mm and ~0.5mm on the inlet and exhaust respectively. If they have zero clearance then bad things are happening. With nothing else being wrong, it would mean that the valves would be held slightly (ever so slightly) open when they are supposed to be closed and it should have all sorts of problems when running, caused by leakage in/out through the valves. Or, zero clearance can indicate severe valve seat recession. None of it is good. Have you used a piece of hose as a stethoscope to try to localise the noise?  
    • Sorry for reviving an old post, but I'm having the same hot idle tick issue. Did anyone ever find out what it was?  I have checked/ replaced Injectors Coils checked Lifter clerance (is at zero) Checked Cam lobes Replaced exhaust gasket and studs Would appreciate any advice this is driving me nuts  
    • There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
    • What HVAC actuator is under the steering wheel? Do you mean on the RHS of the centre console, immediately to the left of your shin? If so, then yes, it is probably that one, because that is the mode door actuator, and from what I know, it's still a pain in the arse to replace. I don't know about whole dash out, but you certainly have to rip into the centre console section. I don't know if it's covered in the workshop manual, as I haven't spent much time looking at those parts of it. (and by "the workshop manual, I mean the R32 GTR one, which is the most comprehensive one we have, and it should be similar enough between that and later cars to serve as a guide).
×
×
  • Create New...