Jump to content
SAU Community

Recommended Posts

Hey guys,

I have a rb26/30 with all the goodies in it, I am wanting to run 35+psi on E85 and i have been told that the ignition has to be changed to do so. Can you big hp guys recommend a setup to run as i am chasing 750rwhp through my glide. cheers

Link to comment
https://www.sau.com.au/forums/topic/410235-rb2630-ignition-setup-help/
Share on other sites

http://www.aemelectronics.com/high-output-igbt-inductive-smart-coil-1240

This is what I would use - best inductive ignition system I've seen.

I tend to prefer running inductive ignition system compared to cdi on almost all applications - especially on street cars.

http://www.aemelectronics.com/high-output-igbt-inductive-smart-coil-1240

This is what I would use - best inductive ignition system I've seen.

I tend to prefer running inductive ignition system compared to cdi on almost all applications - especially on street cars.

They look like awesome coils. No CDI or igniter unit required. Less to go wrong?

How have they performed for you rob?

Why do you not like CDI systems? Because of the electrical interferance and low dwell time?

They look like awesome coils. No CDI or igniter unit required. Less to go wrong?

How have they performed for you rob?

Why do you not like CDI systems? Because of the electrical interferance and low dwell time?

I'm about to turn up the wick on a certain engine that will be in the vacinity of 2000hp with these coils - currently at 1260hp and no issues with 1.1mm at 18psi. Have seen them not misfire with 1.1mm gap at this boost with mixtures as rich as lambda 0.67.

CDI is good if you want high peak secondary current and minimal dwell time - issues I have with CDI is eletrcial interference and low spark duration coupled with extra cost. Only thing with these coils and LS2 series coils is the dwell time can be as large as 5ms at 14V for full spark energy which can be a bit much on non sequential setups with rapid accelleration rates and flat shifting. Doubt most people would run into this issue though.

Edited by rob82

I'm about to turn up the wick on a certain engine that will be in the vacinity of 2000hp with these coils - currently at 1260hp and no issues with 1.1mm at 18psi. Have seen them not misfire with 1.1mm gap at this boost with mixtures as rich as lambda 0.67.

CDI is good if you want high peak secondary current and minimal dwell time - issues I have with CDI is eletrcial interference and low spark duration coupled with extra cost. Only thing with these coils and LS2 series coils is the dwell time can be as large as 5ms at 14V for full spark energy which can be a bit much on non sequential setups with rapid accelleration rates and flat shifting. Doubt most people would run into this issue though.

Isn't it easier to ignite the air/fuel on an engine that has a much larger bore like that one?

http://www.aemelectr...smart-coil-1240

This is what I would use - best inductive ignition system I've seen.

I tend to prefer running inductive ignition system compared to cdi on almost all applications - especially on street cars.

Certainly look like great value for money - any potential downside?

Isn't it easier to ignite the air/fuel on an engine that has a much larger bore like that one?

Yep - generally the higher the torque the greater the cylinder pressures so the higher harder it is on the ignition system...

I haven't try these coils on an xr6t, because they wouldn't fit very well but the are probably one car that really pushes a coils ability and I know just the car to test on. If I get to test them on that car I will let you guys know how they hold up?

Also the only other downside is that they aren't cop...

Edited by rob82

We have run these coils on a 140mph 1jz running nos for the last 12 months.

Very good coil charge time with amp saturation. Would I run them on 50+psi probably not.

That's not to say that they wouldn't do it, I would not like to commit and say they will and then have to fit CDI any way.

I have found that inductive just seems to run nicer with back to back tests. Engines just sound that little bit happier.

We have run these coils on a 140mph 1jz running nos for the last 12 months.

Very good coil charge time with amp saturation. Would I run them on 50+psi probably not.

That's not to say that they wouldn't do it, I would not like to commit and say they will and then have to fit CDI any way.

I have found that inductive just seems to run nicer with back to back tests. Engines just sound that little bit happier.

Everyone likes a happy engine don't they

Well at the end of the day, after cylinder pressure and temp, Egts, MBT, BSFC, gudgeon pin size, exhaust wheel temp, oil pressure and temperature all we are doing in pleasuring the engine just how it likes it.

Golden rule, give the engine what it wants. If it wants CDI it gets CDI. If it want 28 degrees of ignition timing at 30psi of boost and a 175 shot of gas then give it 28 degrees.

Its kinda like an extremely high maintenance gf. You work and work for months just to be able to take it out and show it off to your friends then it craps in your face just to keep you keen (Or on the highway at the top of 4th gear) when it doesn't get its way.

The only downfall i can see with these is they are a damn big coil. Mounting 6 of these may not be the easiest to do so.

But i do like, and these have risen to the No 1 on my most likely coil to buy for my setup.

I'm about to turn up the wick on a certain engine that will be in the vacinity of 2000hp with these coils - currently at 1260hp and no issues with 1.1mm at 18psi. Have seen them not misfire with 1.1mm gap at this boost with mixtures as rich as lambda 0.67.

CDI is good if you want high peak secondary current and minimal dwell time - issues I have with CDI is eletrcial interference and low spark duration coupled with extra cost. Only thing with these coils and LS2 series coils is the dwell time can be as large as 5ms at 14V for full spark energy which can be a bit much on non sequential setups with rapid accelleration rates and flat shifting. Doubt most people would run into this issue though.

So these would be worth a try on my RB30/25 aiming at 330 - 350 awkw with a rev limit of 6800 and no flat shifting or would I need to change my Link G4 with 4 ignition channels for a Link Extreme to allow sequential firing?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, the latter. No diff should have a centre replaced without checking clearances because its unlikely to be the same as whatever came out. Not that that stops most people just checking a new centre in
    • Major thread necro but how bad of a job is it to DIY? Looking at it online it looks like if you reuse your ring and pinion as long as those are in good condition it should be fine to just pull the axles/front cover and replace the diff that way? Or should I be replacing everything and doing preload measurements/gear mesh testing like the factory service manual mentions for the rear diff?
    • in my list I had the R33 GTR as the best Skyline. Infact I had all GTR's (33>34=32), the NSX, the GTO, the 300ZX, the 180SX, the S15 better than the FD RX7. I had the MR2 and the A80 as 'just' better. I also think the DC5R Integra looks better but this is an 01 onwards car. I also think the FC>FD. It's almost like aesthetics are individual! The elements @GTSBoy likes about the FD and dislikes about the 180 are inverse in my eyes. I hate the rear end of the FD and it's weird tail lights that are bulbous and remind me of early hyundai excels. They are not striking, nor iconic, nor retro cool. The GTO has supercar proportions. I maintain these look much better in person (like the NSX) especially with nice wheels and suspension which is mandatory for all cars pretty much. Some (or all) of these you have to see in person to appreciate. You can't write a car off until you see one in the flesh IMO. Like most people we probably just like/dislike cars which represent certain eras of design or design styles in general. I also think the 60's Jag E type looks HORRIBLE, literally disgusting, and the 2000GT is nothing to write home about. FWIW I don't think the Dodge Viper Gen1's have aged very well either. You can probably see where I rate bubbly coupes like the FD. I know we're straying now but the C4 and C5 absolutely murder the Viper in the looks department as time goes on, for my eyes. Wouldn't surprise me if people who love the FD, also love the MX5, Dodge Viper, Jag E Type, etc etc.
    • I used to hate R31s, and any of the other Nissans that led up to it, and any of the Toyotas with similar styling, because of the boxiness. They were, and remain, childish, simplistic, and generally awful. I appreciate R31s a lot more now, but only the JDM 2 door. The ADM 4 door (and any other 4 door, even if they are unique compared to our local one) can eat a bowl of dicks. The Aussie R31 is also forever tarnished by their association with stereotypical bong clutching Aussie R31 owners of the 90s and early 2000s. I think the Nissans of the 70s (other than 120Y/180B/200B) are far superior looking to the 80s cars. The 240K era Skylines are boss. The same is broadly true of Toyotas. Hondas don't ever register in my thinking, from any era. Mitsus are all horrid shitboxen in any era, and so also don't register. Subarus are always awful, ditto. Daihatsus and Suzukis also don't generally register. They are all invisible. I think the SW20 MR2 looks fiddly. The 3000GT/GTO is like that but way worse. Too many silly plastic barnacles and fiddly gimmicks ruined what could have been a really nice base shape. Kinda-sorta looks like a big heavy ST165 Celica coupe (and I'm not sure if that's a good thing or a bad thing). I think the 180SX is dreadfully bland. It's not bad looking. But it has no excitement to it at all. It's just a liftback coupe thing with no interest in its lines, and bad graphical elements (ie wide expanses of taillight plastic on the rear garnish). The S13 Silvia is a little better - getting closer to R32 shapes. But still....bland. S14? Nope. Don't love it. S15...a little better. Probably a lot better, actually. Benefits from not being like a shrunk in the wash R34 (where the S13 was a shrunk in the wash R32 and the S14 looked like a Pulsar or something else from the stable on Nissan mid 90s horrors). The Z32 was hot as f**k when it came out but hasn't aged as well as the A80. Keep in mind that I think the R33 is the most disgusting looking thing - and out of all the previous cars mentioned is objectively closest to my precious R32. It's just....real bad, almost everywhere you look. And that is down to the majority of what was designed in the 90s being shit. All Nissans from that era look like shit. Most other brands ditto. In that context, the FD absolutely stands out as being by far the best looking car, for reasons already discussed. Going behind the aesthetics, the suspension alone makes it better than almost any other car.  
    • If they just called it the "Mazda Tiffany", it would have been spot on.
×
×
  • Create New...