Jump to content
SAU Community

Recommended Posts

On 05/11/2016 at 6:29 PM, Terry_GT-R34 said:

R32 GT-R V-Spec II N1

Terry-17_zpsq9jsy8mi.jpg

 

R33 GT-R V-Spec N1

Terry-103_zpshtjg5oz4.jpg

 

R34 GT-R V-Spec N1

Terry-31_zpsh61mvvfn.jpg

 

...as they are to-day.

 

C'mon guys! You do realise don't you that the thread says, "Engines / Engine Bays" Plural???

On 11/8/2016 at 7:33 AM, Terry_GT-R34 said:

 

C'mon guys! You do realise don't you that the thread says, "Engines / Engine Bays" Plural???

Well you have 3 GTR's....

On 11/5/2016 at 8:29 PM, GTR-N1 said:

R32 GT-R V-Spec II N1

Terry-17_zpsq9jsy8mi.jpg

 

R33 GT-R V-Spec N1

Terry-103_zpshtjg5oz4.jpg

 

R34 GT-R V-Spec N1

Terry-31_zpsh61mvvfn.jpg

 

...as they are to-day.

WTF you have 3 N1 GTRs?!?!?... my gawd lol

  • 2 weeks later...
  • 2 months later...
  • 2 months later...

Just a dodgy camera phone photo, but finishing off the carbon fibre engine dressings. Just need to give it a clean up. Has been a bit neglected lately. Need to wait for the cam covers to yellow a bit to match the coilpack and cam gear covers though

 

34558488981_5680d09b74_k.jpg2017-05-16_02-51-25 by

Edited by 89CAL
  • Like 3
  • 3 years later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It was roughly 3.5 hours.    car went in around 11:00 and I was done around 2:30 He did the initial runs, install the BC and then Nistune install and tune.  The best part was sitting in the lobby and hearing the skyline on full throttle at the dyno 😂😂
    • Glad it all went smooth. How long did the tuning process take?
    • Yeah that was kind of the same feedback my tuner gave me.  the boost tee is until I can sort out my plan for the electronic boost controller and what I’d get, where I’d mount the dash etc.  I’m happy with this until I can figure it out. Not a big fan of the A-pillar gauges. I’d like to get a clean install of the boost gauge - something digital like GFB.  Something like that might fit neatly where the ashtray is and look clean. I feel like replacing the OEM triple gauge is a bit extreme for a weekender like my skyline. And it’s not making crazy power to need all the additional sensors/gauges. 
    • I'm about to swap my box to Tremec T56 Magnum F & initially thinking of re-using my DCS twin plate (can get it re centred for the bigger spline) but it's been called out the box will be noisy (rattle) as the clutch is unsprung.  So I'm doing as much research as possible. I'm not so worried about holding the power as I'll go the track version which on paper will hold the maybe 1000hp I make. It's the longevity I worry about. DCS told me they don't use a sprung centre as it's just something that can break. The uni clutch has a very complicated sprung centre. Any one had or heard about any issues with it failing? Thanks in advance.
    • Auto is at least 10% (from my real, actual experience with different torque converters and manual on the same setup) ~185rwkw at 11.6psi (peak!) is entirely what one would expect without a FMIC or anything else on the intake, it does bleed off towards the higher RPM so it's what, 9psi there? Note: There is nothing that can be done about this with a manual boost tee. If you want to hold it steady and gain more top end, well - You will need electronic boost control.....
×
×
  • Create New...