Jump to content
SAU Community

Recommended Posts

Trying to fix my A/C in My wifes R33 GTST but am finding dead ends wherever I look.

I have Checked all relays and continuity of all wiring. I have also ruled out low pressure sensor. The system is holding pressure and the compressor runs and cools the car when I earth the a/c relay or bridge the pressure sensor plug. I have also check the eccu for correct voltage at pin out 46. The only problem I have found is there is no dip in voltage of pin out 9 when the on off switch is activated.

Is There any auto elects out there that have some answers.

Any other ideas would be awesome.

Link to comment
https://www.sau.com.au/forums/topic/410794-trouble-shooting-ac-in-r33/
Share on other sites

just put another relay in, I had the same issue trying to fix Ph@t-G's foglights & horn, The relays were fine, checked continuity, everything.. then I was like fine I'll just try different relays. Turns out the relays were fried, they couldn't handle the current.

I guess I will just cross that one off the list too. Doesn't seem to want to be fixed. The strange thing is It cools all the relays will work when bypasses are made at varying points. The climate control module is switching correctly and the compressor is working and cooling the car. The only thing is that if there is not an earth to trick the system, nothing runs. Starting to get fricken real annoying.

I guess I will just cross that one off the list too. Doesn't seem to want to be fixed. The strange thing is It cools all the relays will work when bypasses are made at varying points. The climate control module is switching correctly and the compressor is working and cooling the car. The only thing is that if there is not an earth to trick the system, nothing runs. Starting to get fricken real annoying.

hrms, maybe the engine harness is loose? or even the interior loom to engine/ecu harness is loose.. check those connectors.. they should mate into the ecu loom

I thought that too. I went to a wrecker and tried two other ecu's making no change. The other thing I'm thinking of trying is pulling out the the unit under the dash and checking the thernistor. Just about out of ideas. I am thinking that if that resistor is no good the the computer won't allow the a/c to be turned on. Its just a matter of working out what needs to come out to get to it.

Had air con re-gassed. That's when all this started. The system had absolutely no gas in it . But there are no leaks and as I have said before. The compressor runs and cools when earthed. But not when using climate control. It may be taking a while to fix this. But I'm not going to let it beat me. I have had three profesionals look at it so far and I seem to be doing all the research. On the plus side I know how the car is being pulled apart and put back together and not having to pay someone by the hour to be removing a'll the interior bits and pieces is also a save. I'm going to know the r33 pretty well after all this. Lol.

is there a -ve current going to the A/C relay at least? I am guessing here, but have you check the A/C fan relay as well? I would be surprised if the A/C compressor & A/C fan relays are connected in series.

Have you got yourself a full wiring diagram to follow?

If you do, start at one point and work through the entire wiring system.

A/C Clutch should get a 12V+ current to the wire for the clutch and grounds through the body of the compressor. Shouldn't be a 0VDC current.

I have two different wiring diagrams although they do not show the complete wiring of the a/c components. They do however show the car wiring to relays. They do not show the thermistor or the other sensors or components.

What I have done this evening quickly was look closer at the relay wiring. If I add earth to pin 1 on the compressor relay, while it is plugged in, it closes the circuit. Then the climate control unit will turn the compressor and A/C on and off. The issue now is that the compressor does not cut out when it should. The idle advance drops and raises the idle when the compressor should cycle on and off but the compressors remains on.

  • 2 weeks later...
  • 2 weeks later...

iv had the trouble in my R33 of my ac switching on and the often (but not always) off again after only 5-10 secs of being on (this is in A/C on mode with 18 degrees selected so technically should run indefinately in warm weather as the interior isnt 18degrees before it switches off sometimes). Sometimes it doesnt even switch on.

THo there is no constant situation (like hot or cold ambient) where it runs, is intermittent or doesnt switch on in.

There is plenty of refridgerant as the view glass is nice n green when on and the air is nice and cold.

Iv run the diagnostic mode and no faults.

anybody know what might be the cause of this or experienced it?

otherwise can you access all of the cars sensors via a consult cable and program? im sure that one of the sensors must be shitty and so going outside its operating range quickly and then switching the AC off. Tho its problem doesnt show in diagnostic mode...

Anybody? (i cant go another summer without it working)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yuck. But it's kinda the same principle, moving timing around to make car run bad but sound good.... I went for a more spirited tuning drive to iron out a few things. Car no longer stalls, and it loved to dip RPM low when you clutch in. After tuning this (and the 4-5 tables that HPTuners/LS1 OEM ECU wants for idle air correction) it's now behaving somewhat normal. All expected because there's a new TB, new Intake manifold and that new TB which is 102mm vs 78... has an entirely different IAC passage which is smaller because ????? Unfortunately at this point I went to make further fine tuning changes to avoid it flaring up, you know... _tuning_ the HPTuners dongle died. Well to be more accurate - The USB cable died in a fashion that anyone who has ever charged a phone will recognize. After the app demanding I resync it 50 or so times (which all 'succeeded' but all failed) the device does not want to sync and I've logged a ticket with support to see if it's fixable. US Support said it was a 'storage issue' but after removing the SD card inside it and formatting it/fixing it the issue does persist. Unfortunately usually the fix is "Turn in your old dongle and pay $700 for the upgraded one" it's cheaper because I get some free licence credits I unfortunately don't need. However I'm 10 minutes down the road from HP Tuners AUS/VCM so at least I won't need to post it, and logged a new ticket for support over here. Definitely drives different. My SOTP dyno believes it's probably making 310-320kw instead of the 280 before.  It scrambles for traction a little now whereas it previously different. It drives like a bigger cam car up top even though the cam is smaller, likely due to the cam not being advanced 6 degrees. The timing is deliberately low and the fuel is very rich so who knows if this will improve on the dyno. It may, imperceptably. Also funny is removing the pineapples definitely makes the car squat more and axle tramp less. So this behavior of having more top end, squatting more, and scrabbling for traction more makes me think = more power. But I could have just been sitting on the threshold of that kind of behavior before. Time will tell if my butt dyno is calibrated right. I need the exhaust leaks fixed before dyno tune for obvious AFR related reasons - I repositioned the pipes but I'm not confident it's fully sealed even if it is better. At least the car does drive around while I cannot tweak/tune it for now. And I have aircon again. medium success!
    • Don't use that manifold. Please don't use that manifold. Sunk cost fallacy is not worth the later pain. None of these will be relevant to the change that will come from the different turbo and manifold. As in, the effect of the exhaust will be nil, regardless of what else is changed. And all the cam and fuel system stuff is not changing either way, so has no effect. The turbo and manifold (and to a small extent the wastegate)....big change.
    • Just wanted to say thank you for your input   my man (lead mechanic by trade) and I have done a heap of work as you can imagine just to make the hot side work with the dump pipe, stupid massive intake on turbo, trying to get the waste gate on was not fun.  I’m kinda getting to the point where I don’t know if I try and make this work and not throw all this cash and time away or do I scrap the lot and start again? the Apexi I’ve got was tuned for a few slight differences:   Tomei pon cams (mine are stock neo) Turbo smart 38mm external waste gate (mines 45mm replumbed) with stainless screamer pipe  3inch turbo back exhaust with high flow cat Sard 800cc top feed injectors Sard adjustable fuel pressure reg    
    • Out here E90s are the cheapest way into a sporty-ish car because everyone knows just how expensive the repairs can get. 8-10k USD for an automatic 335i. 
×
×
  • Create New...