Jump to content
SAU Community

Recommended Posts

hi im sure this has been covered before but do i need a "CAMS" approved cage if i wish to have a cage to compete in club style events such as sau etc? or is a safety21 cusco bolt in cage ok? at this level?

i just see a few cars running what look like bolt in cusco cages in there cars? i have read the cams rules and they do permit certain styles of bolt in cage anyhow so hence my confusion.

cheers Marc

For club sprints / Level 2 speed events, you should technically require a cams compliant cage. WRX club has been lenient in the past on this requirement as I've seen all kinds of bolt in, and non compliant designs pass scrutineering. From Jan 1 2013, the requirement will be to have padding in contact bars for all competition levels. Again, it's up to the club scrutineers on the day to enforce it.

SCHEDULE J - SAFETY CAGE STRUCTURES - were safety cage is required

From 1st Jan 2013 ALL competitions will require minimum SFI 45.1 or the preferred FIA 8857-2001 roll cage padding

11. PROTECTIVE PADDING

11.1 Helmet and Head Protection:

(a) Where the helmet of an occupant could come into contact with the safety cage, protective padding shall befitted in that area, which complies with:

(i) International competition and below, FIA standard 8857-2001, type A (see FIA Technical List No 23 “RollCage Padding Homologated by the FIA”); or

(ii) For national competitions and lower, SFI specification 45.1.

(b) Implementation DatesPadding of the type specified in 11.1(a) is required as follows:

• Any FIA category vehicle (eg, Group N, Super 2000) – refer FIA Appendix J, Article 253 – currently in place;

• National competitions – from 1 January 2012; and

All competitions – from 1 January 2013. The use of the specified padding is highly recommended in the meantime.

11.2 Body Protection:

Where the body of an occupant could come into contact with the safety cage, it isrecommended that flame retardant padding be fitted. FIA standard 8857-2001 or SFI specification 45.1padding is recommended.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Update: I got the magnet out. I bought 3 different flexible magnetic reach tools, but none of them worked. The magnet on the tip was all less than 2lbs of force, so i had to buy a special cylindrical magnet that had a pull force of 9lbs.  The magnet finally came in the mail yesterday, so i got under the car to get to work. The super strong magnet isn't that long, so i only have about 1 finger pinch lengths to hold it. I was so scared when i was going in the hole, that the 9lb magnet would just fly away inside the oil pan never to be seen again, but i had my butt cheeks clenched and finger gripped on that thing so tight, i managed to get it to suck the other magnet out.  It was a victory for me last night.         
    • Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
×
×
  • Create New...