Jump to content
SAU Community

Recommended Posts

I got an Automatic 4-dr GTT and it sometimes engine sounds like subaru then the TCS and SLIP lights come on simultaneously, and it's getting worse. It happened like twice a week and now happens almost every time I start the car. Have the ECU scanned and it results a 6c engine system fault code. Does anyone know what would lead the the subaru sound and the lights come on and what the 6c fault code means?

post-99278-0-39801100-1349610175_thumb.jpg

Thanks

Link to comment
https://www.sau.com.au/forums/topic/411014-tcs-slip/
Share on other sites

I got an Automatic 4-dr GTT and it sometimes engine sounds like subaru then the TCS and SLIP lights come on simultaneously, and it's getting worse. It happened like twice a week and now happens almost every time I start the car. Have the ECU scanned and it results a 6c engine system fault code. Does anyone know what would lead the the subaru sound and the lights come on and what the 6c fault code means?

post-99278-0-39801100-1349610175_thumb.jpg

Thanks

Coilpacks failing

Or tcs is

Seems to be the end of life for r34 gtt tcs i know of at least 5 failures in the past months including mine

Some say coilpacks but mine had been replaced with shitfires ( no better then any other brand and cost a butt load)

Ended up the tcs was sensing slip and confused the abs as well , cheaper to grab a used tcs complete off a wreck , they seem to be not happy for rebuild once removed the switch fails

Auto gtt work fine on 5 spd

5 spd wont work on auto need extra plug that 5 spds dont have , many years have many part #

they changed parts a lot from 98-2002 so pointless to find exact part #

Nissan is a goldmine cost wise for that part

Buy a gasket for throttlebody and expect to have to order it from japan nissan has few if any In Country , do it fast yours is close to leaving you stranded with only 2000 rpm available max

Reset the ecu afterwards and reset tps it will be off a bit

dont waste a bunch of cash chasing codes because its not the fix , check coils but money is on tcs failure imminent

Google sau its been covered a bunch lately

Link to comment
https://www.sau.com.au/forums/topic/411014-tcs-slip/#findComment-6568517
Share on other sites

Had the same issue with my R34. It sounds like a Suburu coz its not running on all 6 cylinders. Its not running on all 6 cylinders coz a coilpack is stuffed & that is why the traction control light & slip light is coming on. I changed my coilpacks & problem is fixed. Only difference I had was my engine light came on too.

Edited by B-Boi34
Link to comment
https://www.sau.com.au/forums/topic/411014-tcs-slip/#findComment-6569573
Share on other sites

Had the same issue with my R34. It sounds like a Suburu coz its not running on all 6 cylinders. Its not running on all 6 cylinders coz a coilpack is stuffed & that is why the traction control light & slip light is coming on. I changed my coilpacks & problem is fixed. Only difference I had was my engine light came on too.

My engine light came up as well ^^

What coilpacks did you get and how much are they?

Link to comment
https://www.sau.com.au/forums/topic/411014-tcs-slip/#findComment-6569691
Share on other sites

My engine light came up as well ^^

What coilpacks did you get and how much are they?

I have splitfire but one failed at a year and they refused warranty , i got offered a group buy of red superspark type for about 300 a set ? Splitfires vary between450-600 for gtt

The best option MSD chevy ls truck coils and some mods to run leads to sparkplugs , cheaper , way more power , dependable long term

Drawbacks a lot more work to setup

Room to put the 6 coilpacks besides on top of cover , even a a dual pack like a 6 cyl commo uses takes room

Overkill unless your boosting it up a fair bit

Damn msd should make replacements grrrrrr

Link to comment
https://www.sau.com.au/forums/topic/411014-tcs-slip/#findComment-6569708
Share on other sites

what should i get if i want a cheaper one but longer lasting one, I mean on daily basis, what is suggested?

From a electronics basis , all of the coil packs are similar , any aftermarket one will have a bit more spark then factory but most are exactly the same internally and the laminated windings are the same thickness , so any brand

update the grounds to the coils and clean up mounting area improves life and power

I have a daisy chained 4 ga ground and that stopped mis fires on splitfire using iridium's

So for a daily any brand , just watch out you need the ones for neo gtt on r34 they dont interchange

Link to comment
https://www.sau.com.au/forums/topic/411014-tcs-slip/#findComment-6570350
Share on other sites

My engine light came up as well ^^ What coilpacks did you get and how much are they?

I put in Spitfires & issue went away. They were $500.00

Iv read many good things about them & most ppl on here say go OEM or Spitfires.

OEM is more expensive

Link to comment
https://www.sau.com.au/forums/topic/411014-tcs-slip/#findComment-6571204
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • On the compressor side it looks like the best, if your head setup will support doing 100-110lb/min at 30psi-ish boost.   The G45-1350 compressor looks ideally better if you need closer to 40psi for it, given both the G40 1150 and G42 1200 look like they'll be around the 100lb/min mark at 35psi and dropping from there.   Bear in mind the turbine sides are all different between those three turbos, so that COULD be an influencing factor for how they all perform in the real world as well.   Not sure if you've made a conscious decision to only look at Garrett or not, but at least on paper the XRE7169S matches or beats those other three at everything from 30psi up and just going from wheel size alone likely to be at least as responsive as the G40 1150 and seem to behave closer to G42s in terms of turbine flow.
    • @Lithium  looking for a turbo for my Rb30. Want to make sure I understand this correctly.   If I want to stay 40psi or under my best choice of these 3 is actually the smaller G40-1150 ?
    • Massive ups for MTHire also. Could not have done the subframe bushings job without hiring the tool from them. Process was super easy and cost me around 25% of the cost of the tool. If you need a one-time tool to do something, check them out. (Paid for the rental myself, no sponsorship here.)  
    • I'd suggest calling Unigroup, they have a lot of experience with these, access to reliable fabricators etc. Of course it will cost but at least you can trust what they tell you
×
×
  • Create New...