Jump to content
SAU Community

Recommended Posts

i need some help, tried doing a search but no luck. i bought a R32 front half to get the engine and other parts to get my cefiro going. i like how the r32 gauge cluster looks and wanted to use to replace the cefiro cluster with it. does anyone have the wiring diagrams for both clusters, is this an easy task?

thanks

Link to comment
https://www.sau.com.au/forums/topic/411382-r32-gauge-cluster-into-a31/
Share on other sites

Not sure on the difficulty of the task, but I've seen it done more than once in pics.

For some reason it's a common mod on Cefiro's around Asia (sold outside of Japan), but they're all RB24S from factory, so, at a guess I'd say it's likely they buy R32 halfcuts for the 20DET and manual box, and also use the body loom out of the halfcut to put the dash cluster ??

From what I remember, some of the gauges on the side of the cluster are close to the border after you put the surround back in place, but it does fit and all gauges visible.

If I get some time I'll hunt around for them pics.

  • 4 months later...

The electrician did the wiring for the gauges once this was done i removed the mounting brackets on the gauge cluster as it was a really tight fit with them. once this is done the next step is basically to remove most of the hard plastic where the old a31 cluster bolted on and just leave the part that holds the spedo cable. after u cut away this u could now fit up the r32 cluster, its a really tight fit so no need to bolt it down. also u need to trim about 1/2 inch of the front plastic that bolts infront the gauge cluster. i don't know all the propper names of the items i described above but i hope it was enough for you to get an idea.

i would upload a pic

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cam I am actually putting in (a few posts up) is actually smaller than my current one. At least duration/overlap wise. All the chop stuff I hear just sounds like an engine running badly, because it is. I then envision driving it around in 1st gear and being massively sad about it bucking to the beat of said chop. There is an idle video of someone with a similar cam floating around the internet, but mine is a custom cam (so is his) so it'll never be the same, plus the fact exhausts are entirely different. What I want to do is put some bullet mufflers/race mufflers in to replace a couple sections straight pipes that currently replace the two extra cats that I don't need. But this is even further down the line!
    • I can tell you now, when the bracket that the little hydraulic ram attaches to snaps, with a subframe, and V8 from an AMG C63 on it, it sounds like someone letting shotgun off right beside you. It leaves your ears ringing, and a huge thankfulness that you never ever put a body part under something heavy that's only supported by a hydraulic lift...
    • Still not a guarantee fix. I used a high quality butyl-mastiq (the black goo that's not really silicone nor polyurethane, same stuff they use from the factory that just spreads out like melty cheese), and I still get lots of water on both sides of the trunk when raining or washing the car. I also suspect the factory spoiler rubber gasket might not be sealing well, so I'm thinking of adding a thin layer of grey silicone around the bolt holes on both sides and see if that's where it also leaks from. The biggest issue is that these cars don't come with a drain hole on each side like other coupes and hatchbacks.
    • I hate it, but maybe he could paint it Monster jam style and call it...godzilla?
    • Would seem to me to be appropriate to go GTR style bar. There are options with and without N1 vent holes, with the GTR lower lip integral (because FG copy). https://justjap.com/search?q=r32 bumper  
×
×
  • Create New...