Jump to content
SAU Community

Recommended Posts

Update.

I picked up the car from Racepace today.

Since the first tune on this car back in October 2012 I have changed the exhaust system and now all the standard intake items have been re-installed.

So I asked them to do a re-tune and make it a bit more responsive (existing tune was a track safe tune so was a bit rich).

So we upped the boost from a previous 18/19psi to 19/20psi this time around and also played around with ignition timing etc.

The end result is AWESOME, the way the car drives now is SO much better. It is so much more responsive and so much easier to drive, less labored and more responsive.

The peak power numbers do it no justice, it is all in the torque and power delivery, so much better now.

Old Track Tune: 349.6 rwkw (4th gear)

New Street Tune: 353.4 rwkw (4th gear)

New Street Tune: 359.6 rwkw (5th gear)

Apparently the dyno was hitting some limiter in 4th gear?

Apparently that is why you see the sudden drop at the end of the power curve?

But the 5th gear run allows the run to rev right out?
Can someone explain this to me?

Here are the old and new 4th gear runs overlayed with POWER and TORQUE:

Dyno01_zpsec0c3655.jpg

Here is the new 5th gear run with POWER and BOOST:

Dyno02_zps801e4b14.jpg

  • Like 1

Here is a photo of the factory BOV's installed.

I am running them as vent to atmosphere for the moment, just until I can source the right BOV return pipe.

Installed a filter just to keep the dust and water out.

20131001_123821_zps00973f54.jpg

Thanks Piggaz,

Good question.

At the end of the day I know there is more that can be done with the current set up, so I will continue to develop it until such point that no more can be done.

When I hit that stage I will then commit to a full rebuild with a forged bottom end.

Next round of mods for the current set up will be...

1) Remove 3" high flow cat and replace with Venom 3.5" in/out 5" body high flow cat

2) Remove Tomei cams and install standard cams

3) Install cam gears

4) Re-tune to suit above changes

I will probably do all this in November / December.

Just got back from Calder Park.

Not sure how I feel? But one thing is for sure, my driving skills are clearly getting worse as I get old.

Anyway, the three runs I did were...

RUN 1: 13.591 @ 119.89mph (2.712 60')

RUN 2: 12.965 @ 114.14mph (2.019 60')

RUN 3: 13.016 @ 116.17mph (2.265 60')

I think the expectations my old R32 GTR set were too high.

In my R32 GTR I ran a 11.573 @ 117.89 mph (1.712 60') with at least 60rwkw less than in my 34 GT-R.

But the 32 was running stock suspension (good squat) and stock 16" wheels with chunky Advan A048R's on the rear - must have made a big difference.

Oh well, it is what it is.

car was clean as last night, job very well done with it...looked a million dollars on the track :thumbsup:
I was a little bummed with the times the car was running, to me it felt like it had a lot more in it,
were you having some issues, or not pushing it hard?

-Ender




Thanks.

I am not sure what the issue was.

I think a combination of bad driving and maybe clutch?

But he mph was OK, so once I get my driving sorted and maybe a new clutch I should run maybe a high 11.

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...