Jump to content
SAU Community

Rb26 Oil In Coolant

Midnight_Blue_32
 Share

Recommended Posts

Midnight_Blue_32 Contributor

Midnight_Blue_32

Posted
Posted

Hey everyone, I recently noticed my gtr would blow a heap of white smoke just after I've warmed it up, so I figured I'd check the coolant and oil. The oil was about half and the coolant was pretty much gunk from the missing oil. So I did a few searches and it turns out that there is a few possible causes, 1. Blown head gasket, 2. Stock oil cooler has failed and either a cracked block or head. Just wondering if anyone who be able to help me out by leading me in the right direction.

The motor is only freshly built with forgies, acl bearings, n1 pumps and a cometic mls head gasket sprayed with some head gasket spray( I forget the name of it but my mate who's a diesel mech said it would be a good idea to be safe). It wasn't smoking until about 3 days ago and oil pres looks fine on a auto meter gauge and I haven't over heated the motor at all, it's always been at half way on the gauge. Although I have upped the boost to 14psi on the od occasion. So I'm kinda stump to what it it could be.

Link to comment
https://www.sau.com.au/forums/topic/411978-rb26-oil-in-coolant/
Share on other sites
trick Proficient

trick

Posted
Posted

Did you use arp head studs on your new motor?

It's a must with big power 26's. Especially if you didn't face the head or block.

I'd say head gasket failure. Do compression test and go from there. Good luck

nobby Collaborator

nobby

Posted
Posted

Seeing as you recon blowing white smoke.

pull spark plugs you could find the problem.

you may find crap in a cylinder, sure sign head gasket.

but a blown head gasket doesn't always leak into cylinders.

oil in water is oil gallery to water path, proberly head gasket.

as for the special sealant guess that's not working hay.

why was a sealant recommended for head gasket, what was it supposed to do / help / fix ?.

NoFigJamHere Enthusiast

NoFigJamHere

Posted
Posted

My monies on cracked block if its got ARP head stud kit, or porrus holes in bores. Have a look at the block on the exhaust side were the oil feed banjo bolt goes into block... look for coolant stains (white-ish green) As someone else also suggested remove ALL spark plugs and if have access to bore scope is best to look inside, if not look for odd coloring on plugs. make sure you keep plugs matched to cylinders so you know were to look once you strip down engine. Hate to bearer of bad news bad you will be at best taking the head off. Ive never seen an OEM heat exchanger leak,crack,fail in 15 years of doing GTRs...

Midnight_Blue_32 Contributor

Midnight_Blue_32

Posted
  • Author
Posted

The motor is about 1500km old, I had the block resurfaced but not the head, I just used the stock head studs and yeah it was the hylomar stuff we used just incase the head was warped.

doo doo Proficient

doo doo

Posted
Posted (edited)

Like Dan said, they say on the install instructions not to use hylomar or similar as there is already a coating on the gasket. Also the finish on the deck should be ok but if the head wasn't skimmed it might not be a fine enough finish for the use of a MLS gasket? (cometic recommend a 50ra finish, but I have no idea how to measure that). And if the head might have been warped (in which case i wouldn't think standard head bolts and a metal HG are going to be the best option..) then the best way to ensure it isn't is to measure it and get a truing cut if you need so you don't have to pull it apart to do it again, which is what you're going to need to do unfortunately

Edited by doo doo
MrStabby Grand Master

MrStabby

Posted
Posted

And if the head might have been warped (in which case i wouldn't think standard head bolts and a metal HG are going to be the best option..) then the best way to ensure it isn't is to measure it and get a truing cut if you need so you don't have to pull it apart to do it again, which is what you're going to need to do unfortunately

Is the old skool straight edge + feeler gauges check worthwhile doing first, rather than going straight to getting it skimmed?

doo doo Proficient

doo doo

Posted
Posted

Is the old skool straight edge + feeler gauges check worthwhile doing first, rather than going straight to getting it skimmed?

Yeah, that's what I meant by getting it measured, no need to skim if in spec. But would still be looking at the surface finish when using a metal HG too, maybe stock finish is ok.

Dobz Experienced

Dobz

Posted
Posted

The motor is about 1500km old, I had the block resurfaced but not the head, I just used the stock head studs and yeah it was the hylomar stuff we used just incase the head was warped.

Were the head bolts you used new, were they tensioned up to the right torque in the right order according to the workshop manual?

It would have been a good idea to skim the head warped or not, for $80-100 it's worth knowing your head is flat and has a good surface finish for sealing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sonicii
      Rv37 400r questions

      By sonicii · Posted

      No idea about the remote start part. If the V37 nav is anything like other Nissan JDM vehicles, you can't get the factory Japanese nav working in australia, a card from a different car almost certainly won't work, those cards are usually matched to the serial number of the DCU.  You could be possibly swap out the components from a AuDM Q50 to get it working, but if this is a new model (2021+) 400R, then you will lose the newer features like ACP/AA.  That said, if you have ACP/AA, just use google maps.. I assume a band expander would be required to get the local radio stations, but don't forget the Japanese FM band is narrower than ours, so you still might not be able to receive all Australian stations. I can't see any reason the tyre pressure sensors won't work here, there is the sensor unit inside the rim and the receiver nearby in the wheel well.  I have never had to change the batteries on my 2015 Q50, so I assume they last quite a while.  A straight battery change shouldn't need them to be re-registered as they are the same unit, that should only be required if you replace a sensor with a new one.   Word of warning, if you ever go into the 'secret' diagnostics mode on the main screen, DO NOT EVER do a 'reset' in this menu, it will erase all of your model specific data in the DCU and you will need a trip to a dealer to re-program it all, which would be particularly painful being an import.  This applies to the AuDM Q50 too.
    • sonicii
      HY51 Fuga Hybrid

      By sonicii · Posted

      There is a known issue with the mix door motor on the Q50 which causes these symptoms, not sure if it is common on the Y51 though.
    • Dose Pipe Sutututu
      UniClutch

      By Dose Pipe Sutututu · Posted

      That ring thing is interesting how it's holding everything together 
    • elir32
      Rv37 400r questions

      By elir32 · Posted

      Hey guys. I have a 400R on its way to Australia from Japan currently and have a few questions I’m hoping others may be able to help with.   Wondering if anyone here has had any luck getting the Sat nav unit to work in Australia!? Assuming the Stereo is as simple as a band expanded and tv won’t work?  Seeing as they’re based off a Q50 which is Aus delivered is there any way to link that system to the nav? Nav modules and head unit are different part numbers and appear slightly different at the rear with plug ins etc. can I put my xtrail sd card into the rv37 and will that convert the maps or update to Australian? Has anyone got any advice here?     also has anyone fitted the factory remote start and Security system once it’s landed in Australia? I put an enquirey to Nissan Japan in via a third party, and they suggested it needs a Nissan Japan dealers device to setup and couldn’t guarantee if one here could do it or not. They can supply and I can physically fit it but to setup I would need a dealers device. Any information here would be appreciated also. I’ve seen one here with it fitted already prior to leaving Japan at a dealer/inporter, so clearly passes compliance and works when fitted Japan and doesn’t need changing here.      also, does the tyre inflation sensors work here? Does anything change with them when the vehicle arrives? Where are they actually situated? I’ve read they have batteries and they need to changing at times and seems like resetting involves the nav system?    any help here would be appreciated and any other aust specific information to help would be great. Looking forward to see what the current generation skyline is like and eager to see how many of the gadgets can be utilised here.  Thanks in advance 
    • Butters
      UniClutch

      By Butters · Posted

      Do need to take it with a pinch of salt. One of the adapter failures, they clearly had setup issues with the flywheel.  One of the slipping ones I spoke to and it was pretty clear the throwout was riding, rather than fix, just swapped to a new clutch.    These clutches are being put in anything from 5k offroad 4x4 beaters, GR yaris, 500hp commodores to 1200hp barra monsters. Bound to be some issues in some of them when they are not a simple bolt in affair due to the changes in height.    There is a lot going on in this picture and unless I did the job myself no way to tell what really happened. 
×
×
  • Create New...