Jump to content
SAU Community

R33 Mdu Coils, R33 Doors, Oem Radiator, Oem Bonnet + Extras

nik.
 Share

Recommended Posts

nik. Enthusiast

nik.

Posted
Posted

hey guys sick of all this stuff laying around taking up space, i stripped my 33 so have a few extras. just ask if somethings needed

MDU coilovers suit r33 $250

approx 30k km on them, no leaks or knocks, drive fine. spring height adjustable only and damper adjustable. 10/8 spring rates.

r33 passenger side door in good condition with 2 small dings, nothin too bad + glass in s1 maroone colour $80

r33 driver side door in good condition with 1 small mark, nothing too bad + glass in s1 maroone colour $80

r33 elec mirrors in maroone, $30 each or $50 together

r33 s1 front bar with indicator lights installed, abit cutout to fit fmic $40

r33 tail lights in maroone, $30 each or $50 together

r33 bonnet in good condition, 1 or 2 small dints, maroone in colour $50

r33 oem radiator, no leaks etc $50

turbosmart 2 stage manual bleed valve $40

r33 hicas rear subframe $80

located in wollongong

pm or preferably sms 0416 129 811 as i dont use sau too often.

Nik

Link to comment
Share on other sites
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Stivo
      R32 goes out in right curves

      By Stivo · Posted

      That's true. However, this problem has started since the tuning. First time with the return journey from the tuning. But yes, the pipe was clogged with dirt and rust. That was certainly due to age
    • Dose Pipe Sutututu
      CD009 RB Conversion

      By Dose Pipe Sutututu · Posted

      Great info @tidi0x  Will definitely be handy for others and maybe me if I decide to keep the shit box H pattern.
    • tidi0x
      CD009 RB Conversion

      By tidi0x · Posted

      Bumping this up one last time.... I wanted to follow up on the clutch slave issue. I realized that what the issue comes down to is the pocket is flat milled, and the cylinder does not want rest flat. So in order to mount it correctly you will need to make a spacer for the fingers so the cylinder is floating. I took two plates of aluminum, drilled some holes and was good. I did still need to make the relief cuts in the bell housing, as even with the spacer the bleed section still interferes. The OE bell housing the mounting holes are raised from the housing.       
    • robbo_rb180
      R32 Gtst - Track Car

      By robbo_rb180 · Posted

      If the event in USA goes ahead will be interesting as it seems the rules will get more cars over here. Apparently the track is laguna seca too. Yeah s15, if I get a the lower dash trims, centre console and change front cross member to standard LCA position will fit clubsprint. See how rules are as i would rather do complete widebody than a bolt on flare to run the 295 with proper clearance.
    • 180 wanabe
      370gt Stock Suspension

      By 180 wanabe · Posted

      If the car is legal height I can't see it being an issue. Found a thread on reddit that might offer some insight.   I got a ticket from a copper in QLD for my S15 being too low. They had this wheel thing on a stick that they put under the car and it hit my exhaust. Anyhow went to an exhaust shop to get the exhaust tucked up/hung a little higher and I wound the coilovers up a smidge. Don't think I even had to go back to the police station unlike when I got defected for having a carbon bonnet when I brought the S15 from the ACT to QLD and had to replace it and then rock up at a police station and have a yougish female officer who knew nothing about cars confirm that I had changed bonnets. Should have just painted the carbon bonnet yellow to match the rest of the car lol
×
×
  • Create New...