Jump to content
SAU Community

Gtr Chassis/ Bare Shell

BRU2AL

By BRU2AL,
in Wanted to Buy

 Share

Recommended Posts

BRU2AL Collaborator

BRU2AL

Posted
Posted

Hi everyone, looking for a R32 or R33 GTR chassis/shell can be bare shell, needs to be complied and registerable.

Looking for straight chassis preferably with no damage, not fussed about bumpers or anything, does not need to be rolling, no interior or dash required. Basically need a donor car to put my interior and running gear into.

Located in Vic, but will travel for the right one.

Link to comment
https://www.sau.com.au/forums/topic/412785-gtr-chassis-bare-shell/
Share on other sites
krzysztof Mentor

krzysztof

Posted
Posted

i have a 33 GT-R however it has some damage front right chassis rail, and bog on real left quarter - would be fine to race though

repair of front chassis rail wouldn't cost a great deal considering the car is now stripped

send me a PM if your interested - has compliance and non VIV so after repair doesn't need to be inspected

Rowdyr32 Mentor

Rowdyr32

Posted
Posted

I have a R32 GTR minus and engine/gearbox and seats.

Every other part is still there including all looms, interior, aircon, suspension etc

It was registered a few years ago in my name but decided to part it out as I never drove it.

Would rather sell it as is but would sell the shell seperate if you want it quickly and not going to mess me around.

I'll let it go cheap to get my shed space back.

$3500 as is for the lot minus wheels and brakes. You can sell what you don't want to make it cheaper.

Or bare shell $2500 stripped out with only hanging panels.

BRU2AL Collaborator

BRU2AL

Posted
  • Author
Posted

Where are you located Gareth? Can you send me pics of the car 0439990557 or email them to me please [email protected] Also it is rolling at the moment?

StreetR32 Contributor

StreetR32

Posted
Posted

have one if Rowdy's doesnt work out, 3000 shell only $5k shell + panels Could do a deal on a R324 style kit with Xenon lights (Extra 3k), located Mornington Peninsula Victoria

post-69371-0-85519800-1352461180_thumb.jpg

post-69371-0-04635000-1351390541_thumb.jpg

most parts available..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...